Dies ist ein
1 Power up the device.2 Set Z-Wave Controller into inclusion mode3 Press the button 3 times within 1.5s to enter inclusion mode.4 The device will be recognized and automatically included into Z-WaveNetwork.
Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.
Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.
Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.
Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.
Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.
Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.
Note : please use the reset procedure only when the primary controller is missing or inoperable.Operation: 1 Power up the device.2 Press and hold the button for 10s until led lights is on, then release thebutton.
Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es
mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz
eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können
Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide
Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw.
Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält
Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller
des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden.
Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes
in den Auslieferungszustand.3>
Das Gerät ist batteriegespeist und damit in der Regel in einem Tiefschlafmodus um
Strom zu sparen. Im Tiefschlafmodus kann das Gerät keine Funksignale empfangen. Daher
wird ein (statischer) Controller benötigt, der netzgespeist und damit immer
funkaktiv ist. Dieser Controller - zum Beispiel ein IP-Gateway - verwaltet eine
Nachrichten-Mailbox für dieses batteriegespeiste Gerät, in dem Nachrichten an dieses
Gerät zwischengespeichert werden. Ohne einen solchen statischen Controller wird die
Nutzung dieses batteriebetriebenen Gerätes sehr schnell zur Entladung der Batterie
führen oder die Nutzung ist komplett unmöglich. Dieses Gerät weckt regelmäßig auf, meldet dies durch Aussenden einer sogenannten
Wakeup-Notifikation und leert dann seine Mailbox im statischen Controller. Dafür
muss bei der Inclusion die Node-ID des Controllers und ein Aufweckinterval
definiert werden. Erfolgt die Inklusion durch einen statischen Controller
wie zum Beispiel ein IP-Gateway, wird dieser Controller diese Konfiguration
automatisch erledigen und in der Regel eine Nutzerschnittstelle anbieten, um das
Aufweck-Interval den Nutzerbedürfnissen anzupassen. Das Aufweckinterval ist ein
Kompromiss zwischen maximaler Batterielaufzeit und minimaler Reaktionszeit des
batteriegespeisten Gerätes. Um das Gerät manuell aufzuwecken, führen Sie die folgende Aktion durch:
Press the button briefly, Led will blink once. Inklusion
1 Power up the device.2 Set Z-Wave Controller into inclusion mode3 Press the button 3 times within 1.5s to enter inclusion mode.4 The device will be recognized and automatically included into Z-WaveNetwork.
Exklusion
1 Power up the device.2 Set Z-Wave Controller into exclusion mode3 Press the button 3 times within 1.5s to enter exclusion mode
Kommunikation zu einem schlafenden Gerät (Wakeup)
Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.
Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.
Gruppen-Nummer | Max. Anzahl Geräte | Beschreibung |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline, all nodes which associated in this group will receive the messages sent by device through lifeline. |
2 | 5 | It is controlling group, all nodes associated in this group will be controlled through BASIC_SET command by the device when device detects a movement event or a tampering event. |
3 | 5 | It is is controlling group, all nodes associated in this group will be controlled through BASIC_SET command by the device when device detects an ambient temperature alarm (Decided by configuration parameter 16, 17). |
4 | 5 | It isis controlling group, all nodes associated in this group will be controlled through BASIC_SET command by the device when device detects an ambient humidity alarm (Decided by configuration parameter 14, 15). |
Z-Wave Produkte können direkt nach der Inklusion im Netz verwendet werden. Durch Konfigurationseinstellungen kann das Verhalten des Gerätes jedoch noch besser an die Anforderungen der Anwendung angepasst und zusätzliche Funktionen aktiviert werden.
WICHTIG: Manche Steuerungen erlauben nur die Konfiguration von vorzeichenbehafteten Werten zwischen -128 und 127. Um erforderliche Werte zwischen 128 und 255 zu programmieren, muss der gewünschte Wert minus 256 eingegeben werden. Beispiel: um einen Parameter auf einen Wert von 200 zu setzen, müsste der Wert 200-256 = -56 eingegeben werden, wenn nur positive Werte bis 128 akzeptiert werden. Bei Werten von 2 Byte Länge wird die gleiche Logik angewandt: Werte über 32768 werden als negative Werte angegeben.
This parameter is configured the sensitivity that motion detect. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
1 - 100 | This value is larger, the sensitivity is lower, and the distance for motion detecting is closer. |
This parameter is configured the value that BASIC_SET for nodes that associated in Group 2, 3, 4.100BASIC_SET = 0xFF (ON).0BASIC_SET = 0x00 (OFF). Grösse: 1 Byte, Voreingestellt: 100
Wert | Beschreibung |
---|---|
0 - 99 | BASIC_SET = 0x00 ~ 0x63 |
100 | BASIC_SET = 0xFF |
This parameter is configured the time interval for temperature and humidity sensor measure the ambient temperature and humidity value. This value is larger, the battery life is longer. And the value changed is not obvious. Grösse: 2 Byte, Voreingestellt: 180
Wert | Beschreibung |
---|---|
30 - 3600 | set the time interval for temperature and humidity sensor measure the ambient temperature and humidity value. |
This parameter is configured the value that differential between current measured and previous report value. If the differential value larger than the settings, device will report this measured temperature value to nodes associated in lifeline. Grösse: 1 Byte, Voreingestellt: 10
Wert | Beschreibung |
---|---|
1 - 127 | Differential Value =Value x 0.1 |
This parameter is configured the value that differential between current measured and previous report value. If the differential value larger than the settings, device will report this measured relative humidity value to nodes associated in lifeline. Grösse: 1 Byte, Voreingestellt: 50
Wert | Beschreibung |
---|---|
1 - 127 | Differential Value = Value x 0.1% RH |
This parameter is configured the threshold value that low level for humidity.When the current ambient humidity value is lower than this configuration value, this will trigger a BASIC_SET = [Value] (The value is decided by Configuration Parameter 10) to control the devices in group 4.Otherwise, The BASIC_SET = 0x00 will be sent to devices in group 4 if these devices have been set to ON. Grösse: 2 Byte, Voreingestellt: 300
Wert | Beschreibung |
---|---|
10 - 999 | Low Level Value = Value x 0.1% RH |
This parameter is configured the threshold value that high level for humidity.When the current ambient humidity value is larger than this configuration value, this will trigger a BASIC_SET = [Value] (The value is decided by Configuration Parameter 10) to control the devices in group 4.Otherwise, The BASIC_SET = 0x00 will be sent to devices in group 4 if these devices have been set to ON. Grösse: 2 Byte, Voreingestellt: 900
Wert | Beschreibung |
---|---|
10 - 999 | High Level Value =Value x 0.1% RH |
This parameter is configured the threshold value that low level for temperature.When the current ambient temperature value is lower than this configuration value, this will trigger a BASIC_SET = [Value] (The value is decided by Configuration Parameter 10) to control the devices in group 3.Otherwise, The BASIC_SET = 0x00 will be sent to devices in group 3 if these devices have been set to ON. Grösse: 2 Byte, Voreingestellt: 150
Wert | Beschreibung |
---|---|
0 - 500 | Low Level Value = Value x 0.1 |
This parameter is configured the threshold value that high level for temperature.When the current ambient temperature value is larger than this configuration value, this will trigger a BASIC_SET = [Value] (The value is decided by Configuration Parameter 10) to control the devices in group 3.Otherwise, The BASIC_SET = 0x00 will be sent to devices in group 3 if these devices have been set to ON. Grösse: 2 Byte, Voreingestellt: 300
Wert | Beschreibung |
---|---|
0 - 500 | High Level Value =Value x 0.1 |
This parameter is configured the specified time window (4s..16s) in which the amount of pulses will trigger a motion event. Grösse: 1 Byte, Voreingestellt: 2
Wert | Beschreibung |
---|---|
0 - 3 | Window Time = [Value] * 4s + 4s |
This parameter is configured amount of pulses during the specified time window which trigger a motion event. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 - 3 | Amount of pluses = [Value] + 1. |
This parameter is configured the no motion detected time after a motion event detects. The device will wait for setting times to ready to next detect. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 - 15 | Blink Time = ([Value] + 1) * 0.5s. |
This parameter is configured the motion detected if enable or not. If 1, Motion detected function is enable. Otherwise is disabled. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 | Motion detected function is disabled |
1 | Motion detected function is enable |
This parameter is configured the time to clear motion event after a motion event detected. Time to motion clear, the device will send a clear event report to controller. Unit: Second. Grösse: 2 Byte, Voreingestellt: 30
Wert | Beschreibung |
---|---|
10 - 3600 | set the time to clear motion event after a motion event detected |
This configuration sets Motion Event Re-trigger is enabled or disabled. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Disabled. The motion event will be sent to controller only when the last motion event is cleared. |
1 | Enabled. The time interval for motion event detecting is defined by configuration No. 4. |
This parameter is configured the Led light on disable or enable. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 | Disable led blink. This configuration is not affecting inclusion, exclusion and reset. |
1 | Enable Led blink when device detects a motion event. |
This configuration sets binary sensor report is enabled or disabled. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Disable sensor binary report when device detects a motion event. |
1 | Enable sensor binary report when device detects a motion event. |
Z-Wave Hardware Platform | ZM5202 |
Gerätetyp | Notification Sensor |
Netzwerkfunktion | Reporting Sleeping Slave |
Firmware Version | HW: 17 FW: 1.80 |
Z-Wave Version | 6.71.01 |
Zertifizierungs-ID | ZC10-18015965 |
Z-Wave Produkt Id | 0x033A.0x0003.0x0100 |
Color | White |
Supported Notification Types | Home Security |
Sensors | Air TemperatureHumidityMotion/No Motion (Binary) |
Security V2 | S2_UNAUTHENTICATED |
Frequenz | XXfrequency |
Maximale Sendeleistung | XXantenna |