Schnellstart

Dies ist ein Z-Wave Gerät vom Typ Schalter (Ein/Aus) für Anwendung in CEPT (Europe). Das Gerät bitte mit dem Stromnetz verbinden, um es nutzen zu können. Um dieses Gerät zu einem Z-Wave Netz hinzuzufügen, führen Sie die folgende Aktion durch:
1) Plug the device into a socket nearby the main Z-Wave controller.2) The LED ring will glow red signalling not being added (remove the device otherwise).3) Set the main Z-Wave controller into adding mode (see the controllers manual).4) Quickly, triple click the B-button located on the casing.5) Wait for the adding process to end.6) Successful adding will be confirmed by the Z-Wave controller.

Achtung: Dieses Handbuch wurde automatisch aus verfügbaren Daten der Z-Wave Alliance Produktdatenbank erzeugt und kann unvollständig sein. Für weitere Informationen steht das Original-Handbuch des Herstellers bereit.


Wichtige Sicherheitshinweise

Bitte lesen Sie diese Anleitung sorgfältig durch. Die in dieser Anleitung festgelegten Empfehlungen nicht zu befolgen, kann gefährlich sein oder gegen das Gesetz verstoßen. Der Hersteller, Importeur, Vertreiber und Verkäufer haftet für keinen Verlust oder Schaden, der durch die Nichtbeachtung der Vorschriften in dieser Anleitung oder anderen Materialien entsteht. Verwenden Sie dieses Gerät nur zu dem vorgesehenen Gebrauch. Beachten Sie die Entsorgungshinweise. Elektronische Geräte jeglicher Art und Batterien dürfen nicht ins Feuer geworfen oder in die Nähe von offenen Wärmequellen gebracht werden.

Was ist Z-Wave?

Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.

Z-Wave ermöglicht eine sichere und stabile Kommunikation indem jede Nachricht vom Empfänger rückbestätigt wird (Zweiwege-Kommunikation) und alle netzbetriebenen Geräte Nachrichten weiterleiten (Routing) können, wenn eine direkte Funkbeziehung zwischen Sender und Empfänger gestört ist.

Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.

Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.

Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.

Produktbeschreibung

FIBARO Wall Plug is a universal, Z-Wave Plus compatible, remotely controlled outlet adapter. This device may be applied wherever you want to control electrical devices with up to 2500W load. The Wall Plug is equipped with a power and energy metering function. It uses a LED ring to visualize the current load with colour changing illumination and operating mode. This is the smallest and most attractive device of this type available in the world. The Wall Plug may be operated using the B-button located on its casing or via any Z-Wave compatible controller.Main features: Compatible with any Z-Wave or Z-Wave Plus Controller. Supports protected mode (Z-Wave network security mode) with AES-128 encryption. Extremely easy installation - simply plug the device into the mains socket. Works as a Z-Wave signal repeater. Active power and energy consumption metering. Current value of the load and operating mode are indicated by the multi-colour LED ring.

Vorbereitung auf die Installation des Gerätes

Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.

Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.

Zurücksetzen in den Auslieferungszustand

Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.

Resetting the device is not the recommended way of removing the device from theZ-Wave network. Use reset procedure only if the primary controller is missing orinoperable. Certain device removal can be achieved by the procedure of removingdescribed in Adding/ removing the deviceon page 6.1) Make sure the device is powered.2) Press and hold the B-button.3) Wait for the LED ring to glow yellow (4th menu position).4) Release the B-button.5) Click the B-button once to confirm selection.6) After few seconds the device will restart with factory settings, which is signalled with the red ring colour.

Sicherheitswarnung für netzbetriebene Geräte

Achtung: Je nach nationalen Sicherheitsnormen kann es nur autorisierten und/oder ausgebildeten Techniker erlaubt sein, elektrische Installationen am Spannungsnetz vorzunehmen. Bitte informieren Sie sich vor der Installation über die Rechtslage.

Hinzufügen/Entfernen des Gerätes (Inklusion/Exclusion)

Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw. Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden. Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes in den Auslieferungszustand.

Inklusion

1) Plug the device into a socket nearby the main Z-Wave controller.2) The LED ring will glow red signalling not being added (remove the device otherwise).3) Set the main Z-Wave controller into adding mode (see the controllers manual).4) Quickly, triple click the B-button located on the casing.5) Wait for the adding process to end.6) Successful adding will be confirmed by the Z-Wave controller.

Exklusion

1) Plug the device into a socket nearby the main Z-Wave controller.2) The LED ring will glow green signalling being added (removing is not necessary otherwise).3) Set the main Z-Wave controller into remove mode (see the controllers manual).4) Quickly, triple click the B-button located on the casing.5) Wait for the removing process to end.6) Successful removing will be confirmed by the Z-Wave controller.

Kommunikation zu einem schlafenden Gerät (Wakeup)

Das Gerät ist batteriegespeist und damit in der Regel in einem Tiefschlafmodus um Strom zu sparen. Im Tiefschlafmodus kann das Gerät keine Funksignale empfangen. Daher wird ein (statischer) Controller benötigt, der netzgespeist und damit immer funkaktiv ist. Dieser Controller - zum Beispiel ein IP-Gateway - verwaltet eine Nachrichten-Mailbox für dieses batteriegespeiste Gerät, in dem Nachrichten an dieses Gerät zwischengespeichert werden. Ohne einen solchen statischen Controller wird die Nutzung dieses batteriebetriebenen Gerätes sehr schnell zur Entladung der Batterie führen oder die Nutzung ist komplett unmöglich.

Dieses Gerät weckt regelmäßig auf, meldet dies durch Aussenden einer sogenannten Wakeup-Notifikation und leert dann seine Mailbox im statischen Controller. Dafür muss bei der Inclusion die Node-ID des Controllers und ein Aufweckinterval definiert werden. Erfolgt die Inklusion durch einen statischen Controller wie zum Beispiel ein IP-Gateway, wird dieser Controller diese Konfiguration automatisch erledigen und in der Regel eine Nutzerschnittstelle anbieten, um das Aufweck-Interval den Nutzerbedürfnissen anzupassen. Das Aufweckinterval ist ein Kompromiss zwischen maximaler Batterielaufzeit und minimaler Reaktionszeit des batteriegespeisten Gerätes.

Um das Gerät manuell aufzuwecken, führen Sie die folgende Aktion durch: Wakeup DescriptionFIBARO Wall Plug is powered with mains voltage so it is always awake.

Einige Hinweise bei Problemen

Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.

  1. Stellen Sie sicher, daß sich das neue Gerät im Auslieferungszustand befindet. Im Zweifel lieber noch mals eine Exclusion ausführen.
  2. Wenn ein Gerät keine Verbindung aufbaut, prüfen Sie , ob Controller und neues Gerät auf der gleichen Funkfrequenz (Länderkennung) arbeiten.
  3. Entfernen Sie nicht mehr vorhandene Geräte als allen Assoziationsgruppen. Ansonsten werden Sie erhebliche Verzögerungen bei der Kommandoausführung spüren.
  4. Nutzer Sie niemals schlafende Batteriegeräte ohne Zentralsteuerung.
  5. FLIRS-Geräte dürfen nicht gepollt werden.
  6. Stellen Sie sicher, daß Sie genügend netzbetriebene Geräte haben, um die Vorteile der Funkvermaschung zu nutzen.

Assoziation - Geräte steuern sich untereinander

Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.

Assoziationsgruppen:

Gruppen-Nummer Max. Anzahl Geräte Beschreibung
1 1 Lifeline reports the device status and allowsfor assigning single device only (main controller by default).
2 10 On/Off (button) devices in this groupwill be switched on or off when relay status is changed using theB-button (done via BASIC SET command frames).
3 10 On/Off (power) devices in this groupwill be switched on or off depending on the current load (done viaBASIC SET command frames).

Configuration Parameters

Z-Wave Produkte können direkt nach der Inklusion im Netz verwendet werden. Durch Konfigurationseinstellungen kann das Verhalten des Gerätes jedoch noch besser an die Anforderungen der Anwendung angepasst und zusätzliche Funktionen aktiviert werden.

WICHTIG: Manche Steuerungen erlauben nur die Konfiguration von vorzeichenbehafteten Werten zwischen -128 und 127. Um erforderliche Werte zwischen 128 und 255 zu programmieren, muss der gewünschte Wert minus 256 eingegeben werden. Beispiel: um einen Parameter auf einen Wert von 200 zu setzen, müsste der Wert 200-256 = -56 eingegeben werden, wenn nur positive Werte bis 128 akzeptiert werden. Bei Werten von 2 Byte Länge wird die gleiche Logik angewandt: Werte über 32768 werden als negative Werte angegeben.

Parameter 1: Always On function

Once activated, Wall Plug will keep the connected device constantlyON, will stop reacting to alarm frames or pushing the B-button.Always On function turns the Wall Plug into a power and energy meter.Connected device will not be turned off upon receiving an alarmframe from another Z-Wave device (parameter 31 will be ignored).In Always on mode, connected device may be turned off only afteruser defined power has been exceeded (parameter 3). In such a case,connected device can be turned on again by pushing the B-button orsending a control frame. By default, overload protection is inactive.
Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
0 function inactive
1 function activated

Parameter 10: High priority power report

This parameter determines the minimum percentage change in activepower that will result in sending power report to the main controllerwith the highest priority in the Z-Wave network.By default, the Wall Plug immediately sends the power report if thepower load changes by 80%.NOTEIn extreme cases, reports may be sent every second if rapid and significant power load changes occur. Frequent reporting may overload the Z-Wave network so these parameters settings should reflect significant changes in power load only.
Grösse: 1 Byte, Voreingestellt: 80

Wert Beschreibung
1 - 99 power change in percent
100 reports are disabled

Parameter 11: Standard power report

This parameter determines the minimum percentage change in activepower that will result in sending power report to the main controllerCompared to parameter 10, the maximum number of reports sent isreduced (parameter 12) to 5 in a specified time interval. In addition,the frames are not sent in EXPLORE mode, which prevents overloadingthe Z-Wave network.By default changes in power load may be reported up to 5 times per30 seconds, when power load changes by 15%.
Grösse: 1 Byte, Voreingestellt: 15

Wert Beschreibung
1 - 99 power change in percent
100 reports are disabled

Parameter 12: Power reporting interval

This parameter defines how frequently standard power reports (parameter11) are sent. By default the Wall Plug sends up to 5 reportseach 30 seconds, provided the power load changes by 15%.
Grösse: 2 Byte, Voreingestellt: 30

Wert Beschreibung
5 - 600 in seconds

Parameter 13: Energy reporting threshold

This parameter specifies the minimum change in energy consumption(in relation to the previously reported), that will result in sendinga new report.
Grösse: 2 Byte, Voreingestellt: 10

Wert Beschreibung
0 energy reports inactive
1 - 500 (0.01-5kWh, step 0.01kWh) - threshold

Parameter 14: Power and energy periodic reports

This parameter defines time period between reports sent whenchanges in power load have not been recorded or if changes are insignificant(not exceeding values of parameters 20, 21 and 23). By defaultreports are sent every hour.
Grösse: 2 Byte, Voreingestellt: 3600

Wert Beschreibung
0 periodic reports inactive
5 - 32400 in seconds

Parameter 15: Measuring energy consumed by the Wall Plug itself

This parameter determines whether energy metering should includethe amount of energy consumed by the Wall Plug itself. Results arebeing added to energy consumed by controlled device.
Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
0 function inactive
1 function activated

Parameter 2: Remember device status after a power failure

This parameter determines how the Wall Plug will react in the eventof power supply failure (e.g. taking out from the electrical outlet).After the power supply is back on, the Wall Plug can be restored toprevious state or remain switched off.This parameter is ignored in Always On mode - the device automaticallyturns ON after plugging it into the socket.
Grösse: 1 Byte, Voreingestellt: 1

Wert Beschreibung
0 device remains switched off
1 device restores the state from before the power failure

Parameter 20: Control of On/Off (Button) association group (2) devices

Controlling devices with the B-Button. This parameter is inactive inAlways On mode (parameter 1).Control as the Wall Plug: switching the Wall Plug onswitch the devices on (parameter 24) switching the Wall Plug offswitch the devices off (parameter 24)Control opposite to the Wall Plug: switching the Wall Plug onswitch the devices off switching the Wall Plug offswitch the devices on
Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
0 control as the Wall Plug
1 control opposite to the Wall Plug

Parameter 21: DOWN value - On/Off (Power) association group (3)

Lower power threshold, used in parameter 23. DOWN value cannotbe higher than a value specified in parameter 22.
Grösse: 2 Byte, Voreingestellt: 300

Wert Beschreibung
0 - 24900 (0.0-2490.0W, step 0.1W)

Parameter 22: UP value - On/Off (Power) association group (3)

Upper power threshold, used in parameter 23. UP value cannot belower than a value specified in parameter 21.
Grösse: 2 Byte, Voreingestellt: 500

Wert Beschreibung
100 - 25000 10.0-2500.0W, step 0.1W)

Parameter 23: The response after exceeding defined power values

This parameter defines the way that 3rd association group devices arecontrolled. Depends on the actual measured power (as parameters 21and 22 settings).
Grösse: 1 Byte, Voreingestellt: 6

Wert Beschreibung
1 turn the associated devices ON, once the power drops below DOWN value (parameter 21)
2 turn the associated devices OFF, once the power drops below DOWN value (parameter 21)
3 turn the associated devices ON, once the power rises above UP value (parameter 22)
4 turn the associated devices OFF, once the power rises above UP value (parameter 22)
5 combination of 1 and 4. Turn the associated devices ON, once the power drops below DOWN value (parameter 21). Turn the associated devices OFF, once the power rises above UP value (parameter 22).
6 combination of 2 and 3. Turn the associated devices OFF, once the power drops below DOWN value (parameter 21). Turn the associated devices ON, once the power rises above UP value (parameter 22).

Parameter 24: SWITCH ON value - On/Off association groups

The value of BASIC SET command frame sent to the devices associatedin On/Off association groups (2, 3).On/Off (Button) association group - in accordance with parameter 20.On/Off (Power) association group - in accordance with parameter 23.NOTESetting parameter 24 to appropriate value will result in: 0 - turning off associated devices1-99 - forcing level of associated devices255 - setting associated devices to the last remembered state or turning them on
Grösse: 2 Byte, Voreingestellt: 255

Wert Beschreibung

Parameter 3: Overload safety switch

This function allows to turn off the controlled device in case of exceedingthe defined power. Controlled device will be turned off evenif Always On function is active (parameter 1).Controlled device can be turned back on via B-button or sending acontrol frame. By default this function is inactive.This functionality is not an overload safety protection nor a short circuitprotection. Circuit needs additional short circuit and overload protection.CAUTIONThe device has a protection that will turn the load off in the case of detecting currentgreater than 110% of rated current. It is a safety function and it cannot be turned off.After its activation the load can be turned on back again by pressing the B-button or sending a control frame. This function is independent of overload safety switch set inthe parameter no. 3.
Grösse: 2 Byte, Voreingestellt: 0

Wert Beschreibung
0 function inactive
10 - 30000 (1.0-3000.0W, step 0.1W) - power threshold

Parameter 30: Active alarms

Define Z-Wave network alarms to which the Wall Plug will respond.
Grösse: 1 Byte, Voreingestellt: 63

Wert Beschreibung
1 general alarm
2 smoke alarm
4 CO alarm
8 CO2 alarm
16 high temperature alarm
32 flood alarm

Parameter 31: Response to alarm frames

This parameter defines how the Wall Plug will respond to alarms (devicesstatus change).In case of values 1 or 2 the Wall Plug is operating normally and LEDring signals an alarm through time defined in parameter 32 or untilthe alarm is cancelled.In case of values 5 to 50 the Wall Plug does not report status change,power changes, ignores BASIC SET command frames. After time definedin parameter 32 or after the alarm cancellation, connected deviceis set to the previous state.NOTEIf Always On function is active (parameter 1), settings of parameter 31 are ignored.
Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
0 no reaction
1 turn connected device on
2 turn connected device off
5 - 50 (0.5-50.0s, step 0.1s) - cyclically change device state with set period

Parameter 32: Alarm state duration

This parameter specifies the duration of alarm state. If a device sendingan alarm frame through the Z-Wave network sets alarm duration aswell, this settings are ignored.
Grösse: 2 Byte, Voreingestellt: 600

Wert Beschreibung
1 - 32400 in seconds

Parameter 40: Power load for violet colour

This parameter determines active power value, which when exceeded,causes the LED ring flash violet. Function is active only when parameter41 is set to 0 or 1.
Grösse: 2 Byte, Voreingestellt: 25000

Wert Beschreibung
1000 - 30000 100.0-3000.0W, step 0.1W

Parameter 41: LED ring colour when controlled device is on

When set to 1 or 2, LED ring colour will change depending on activepower and parameter 40. Other colours are set permanently and donot depend on power consumption.
Grösse: 1 Byte, Voreingestellt: 1

Wert Beschreibung
0 illumination turned off completely
1 colour changes continuously depending on active power
2 colour changes in steps depending on active power
3 white
4 red
5 green
6 blue
7 yellow
8 cyan
9 magenta

Parameter 42: LED ring illumination colour when controlled device is off


Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
0 illumination turned off completely
1 LED ring is illuminated with a colour corresponding to the last measured power, before the controlled device was turned off
3 white
4 red
5 green
6 blue
7 yellow
8 cyan
9 magenta

Parameter 43: LED ring illumination colour at the Z-Wave network alarm detection


Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
0 illumination turned off completely
1 no change in colour. LED ring colour is determined by settings of parameters 41 or 42
2 LED ring flashes red/blue/white
3 white
4 red
5 green
6 blue
7 yellow
8 cyan
9 magenta

Parameter 50: Associations in Z-Wave network security mode

This parameter defines how commands are sent in specified associationgroups: as secure or non-secure. Parameter is active only inZ-Wave network security mode. This parameter does not apply to 1stLifeline group.
Grösse: 1 Byte, Voreingestellt: 3

Wert Beschreibung
0 none of the groups sent as secure
1 2nd group sent as secure
2 3rd group sent as secure
3 2nd and 3rd group sent as secure

Technische Daten

Z-Wave Hardware Platform ZM5202
Gerätetyp On/Off Power Switch
Netzwerkfunktion Always On Slave
Firmware Version HW: 2 FW: 3.15:03.02
Z-Wave Version 6.51.06
Zertifizierungs-ID ZC10-16035016
Z-Wave Produkt Id 0x010F.0x0602.0x1001
Frequenz XXfrequency
Maximale Sendeleistung XXantenna

Gesteuerte Kommandoklassen

  • Basic
  • Multi Channel V4

Erklärung einiger Z-Wave-Begriffe

  • Controller... ist ein Z-Wave-Gerät mit erweiterten Fähigkeiten zur Verwaltung eines Netzes. Dies sind in der Regel Gateways oder Fernbedienungen. Batteriegespeiste Wandschalter können auch Controller sein.
  • Slave... ist ein Z-Wave-Gerät mit erweiterten Fähigkeiten zur Verwaltung eines Netzes. Es gibt Sensoren, Aktoren und auch Fernbedienungen als Slaves.
  • Primärcontroller (engl. Primary Controller)... ist der zentrale Netzverwalter des Z-Wave-Netzes.
  • Inklusion (eng. Inclusion)... ist der Prozess des Einbindens eines neuen Gerätes ins Z-Wave-Netz.
  • Exklusion (engl. Exclusion)... ist der Prozess des Entfernens eines Gerätes aus dem Z-Wave-Netz.
  • Assoziation (engl. Association)... ist eine Steuerbeziehung zwischen einem steuernden und einem gesteuerten Gerät. Die Information dazu wird im steuernden Gerät in einer Assoziationsgruppe hinterlegt.
  • Wakeup Notifikation (engl. Wakeup Notification) ... ist eine spezielle Funknachricht, mit der ein batteriegespeistes Gerät bekanntmacht, daß es im Aufwachstatus ist und Z-Wave-Nachrichten empfangen kann.
  • Node Information Frame... ist eine spezielle Funknachricht, mit der ein Z-Wave-Gerät seine Geräteeigenschaften bekanntgibt.