Schnellstart

Dies ist ein Z-Wave Gerät vom Typ Schalter (Ein/Aus) für Anwendung in CEPT (Europe). Das Gerät bitte mit dem Stromnetz verbinden, um es nutzen zu können. Um dieses Gerät zu einem Z-Wave Netz hinzuzufügen, führen Sie die folgende Aktion durch:
Inclusion: AddAdding RS LED D2 to the Smart Friends system:1 Download Smart Friends app from the app store.2 In the rooms view, activate the edit mode.3 Select the chosen room and press the "Add device" button.4 Briefly press button 5 on the device to set it to inclusion mode. Status LED 8 lights up to show that this mode is selected.5 The app displays a confirmation message once inclusion has been successfully completed.

Achtung: Dieses Handbuch wurde automatisch aus verfügbaren Daten der Z-Wave Alliance Produktdatenbank erzeugt und kann unvollständig sein. Für weitere Informationen steht das Original-Handbuch des Herstellers bereit.


Wichtige Sicherheitshinweise

Bitte lesen Sie diese Anleitung sorgfältig durch. Die in dieser Anleitung festgelegten Empfehlungen nicht zu befolgen, kann gefährlich sein oder gegen das Gesetz verstoßen. Der Hersteller, Importeur, Vertreiber und Verkäufer haftet für keinen Verlust oder Schaden, der durch die Nichtbeachtung der Vorschriften in dieser Anleitung oder anderen Materialien entsteht. Verwenden Sie dieses Gerät nur zu dem vorgesehenen Gebrauch. Beachten Sie die Entsorgungshinweise. Elektronische Geräte jeglicher Art und Batterien dürfen nicht ins Feuer geworfen oder in die Nähe von offenen Wärmequellen gebracht werden.

Was ist Z-Wave?

Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.

Z-Wave ermöglicht eine sichere und stabile Kommunikation indem jede Nachricht vom Empfänger rückbestätigt wird (Zweiwege-Kommunikation) und alle netzbetriebenen Geräte Nachrichten weiterleiten (Routing) können, wenn eine direkte Funkbeziehung zwischen Sender und Empfänger gestört ist.

Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.

Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.

Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.

Produktbeschreibung

Sleek, attractive lines. Opting for the RS LED D2 designer indoor luminaire, you'll be giving your home a real designer highlight with pleasant LED illumination. With its stunning looks and intelligent technology, this light provides the last word in stylish home convenience. Once fitted to the wall or ceiling, the high-frequency sensor switches it 'ON' and 'OFF' in complete silence and all automatically. The light is child's play to install and the function settings on the product are easy to understand too. Your neighbours will be amazed.Smart home included.The optional Smart Friends Box and the free Smart Friends app make it easy to set the RS PRO LED D2 Z-Wave via smart phone or tablet. The light can also be switched ON or OFF via app. Other Steinel products can also be interconnected. If you wish, this also works via remote control when you are out. That completes your own light management system.Along with STEINEL products, Smart Friends solutions from PAULMANN, SCHELLENBERG and ABUS can also integrated. Smart homes from a brand-name provider.

Vorbereitung auf die Installation des Gerätes

Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.

Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.

Zurücksetzen in den Auslieferungszustand

Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.

Returning RS LED D2 to factory settings:Please use this procedure only when the network primary controller is missing or otherwise inoperable.1 Briefly press button e and directly afterwards keep it pressed for 5 seconds.2 Status LED h briefly flashes to show that the light has been reset.3 The device is now no longer included in the Z-Wave system and has been returned to factory settings.

Sicherheitswarnung für netzbetriebene Geräte

Achtung: Je nach nationalen Sicherheitsnormen kann es nur autorisierten und/oder ausgebildeten Techniker erlaubt sein, elektrische Installationen am Spannungsnetz vorzunehmen. Bitte informieren Sie sich vor der Installation über die Rechtslage.

Hinzufügen/Entfernen des Gerätes (Inklusion/Exclusion)

Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw. Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden. Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes in den Auslieferungszustand.

Inklusion

Inclusion: AddAdding RS LED D2 to the Smart Friends system:1 Download Smart Friends app from the app store.2 In the rooms view, activate the edit mode.3 Select the chosen room and press the "Add device" button.4 Briefly press button 5 on the device to set it to inclusion mode. Status LED 8 lights up to show that this mode is selected.5 The app displays a confirmation message once inclusion has been successfully completed.

Exklusion

Exclusion: RemoveRemoving RS LED D2 from the Smart Friends system:1 In the rooms view, activate the edit mode.2. Select the device in the chosen room and press the "delete" button. Press delete and follow the instructions in the app.3 Briefly press button e on the device to set it to exclusion mode. The red status LED h lights up to show that this mode is selected.4 The app displays a confirmation message once exclusion has been successfully completed.

Einige Hinweise bei Problemen

Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.

  1. Stellen Sie sicher, daß sich das neue Gerät im Auslieferungszustand befindet. Im Zweifel lieber noch mals eine Exclusion ausführen.
  2. Wenn ein Gerät keine Verbindung aufbaut, prüfen Sie , ob Controller und neues Gerät auf der gleichen Funkfrequenz (Länderkennung) arbeiten.
  3. Entfernen Sie nicht mehr vorhandene Geräte als allen Assoziationsgruppen. Ansonsten werden Sie erhebliche Verzögerungen bei der Kommandoausführung spüren.
  4. Nutzer Sie niemals schlafende Batteriegeräte ohne Zentralsteuerung.
  5. FLIRS-Geräte dürfen nicht gepollt werden.
  6. Stellen Sie sicher, daß Sie genügend netzbetriebene Geräte haben, um die Vorteile der Funkvermaschung zu nutzen.

Assoziation - Geräte steuern sich untereinander

Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.

Assoziationsgruppen:

Gruppen-Nummer Max. Anzahl Geräte Beschreibung
1 1 Z-Wave Plus Lifeline - Device Reset Locally - Notifications: 0x09 (System)Hardware failure with manufacturer proprietary code (0x03)0x09 (System)Software failure with manufacturer proprietary code (0x04)0x07 (Home security)Motion Begin event (0x08)0x07 (Home security)Motion End event (0x00, 0x08)- Binary Switch Reportlamp state- Multilevel Sensor Reportvalue of internal ambient light sensor
2 16 On/Off Control-Basic Set
3 16 Motion begin/end - Notifications: 0x07 (Home security)Motion Begin event (0x08)0x07 (Home security)Motion End event (0x00, 0x08)
4 16 Ambient light- Multilevel Sensor Reportvalue of internal ambient light sensor

Configuration Parameters

Z-Wave Produkte können direkt nach der Inklusion im Netz verwendet werden. Durch Konfigurationseinstellungen kann das Verhalten des Gerätes jedoch noch besser an die Anforderungen der Anwendung angepasst und zusätzliche Funktionen aktiviert werden.

WICHTIG: Manche Steuerungen erlauben nur die Konfiguration von vorzeichenbehafteten Werten zwischen -128 und 127. Um erforderliche Werte zwischen 128 und 255 zu programmieren, muss der gewünschte Wert minus 256 eingegeben werden. Beispiel: um einen Parameter auf einen Wert von 200 zu setzen, müsste der Wert 200-256 = -56 eingegeben werden, wenn nur positive Werte bis 128 akzeptiert werden. Bei Werten von 2 Byte Länge wird die gleiche Logik angewandt: Werte über 32768 werden als negative Werte angegeben.

Parameter 1: TIME

Duration of light after motion detection.
Grösse: 2 Byte, Voreingestellt: 180

Wert Beschreibung
5 - 900 seconds

Parameter 10: OFF_BEHAVIOUR

Behaviour after BASIC OFF ( and similar commands ).If a transition ( even with zero change ) with a non-default duration isto be processed, the transition cannot be interrupted by any motionevent in any case.for values 1-209 - Lamp is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received.
Grösse: 2 Byte, Voreingestellt: 10

Wert Beschreibung
0 Lamp is switched off and remains so until any new motion event (local or remote) is received.
1 - 100 timeout: 1 second (1) to 100 seconds (100) in 1-second resolution
101 - 200 timeout: 1 minute (101) to 100 minutes (200) 1-minute resolution
201 - 209 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution
255 Lamp is switched off for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation

Parameter 11: ON_BEHAVIOUR

Behaviour after BASIC ON (and similar commands).If a transition (even with zero change) with a non-default duration is to be processed, the transition cannot be interrupted by any motion event in any case.for values 1-209 - Lamp is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received.It then works normally via current motion evaluation.
Grösse: 2 Byte, Voreingestellt: 255

Wert Beschreibung
1 - 100 timeout: 1 second (1) to 100 seconds (100) in 1-second resolution
0 Lamp is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.
101 - 200 timeout: 1 minute (101) to 100 minutes (200) 1-minute resolution
201 - 209 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution
255 Lamp is switched on for TIME (cfg 1). It does not wait for a motion event and works normally via current motion evaluation.

Parameter 12: ON_TIME_OVER

Time limit to stop waiting for motion after timeout of ON_BEHAVIOURor OFF_ON_BEHAVIOUR ( 0-209 ) to prevent staying ON forever whenis no motion.
Grösse: 2 Byte, Voreingestellt: 204

Wert Beschreibung
0 o additional waiting for motion.
1 - 100 timeout: 1 second (1) to 100 seconds (100) in 1-second resolution
101 - 200 timeout: 1 minute (101) to 100 minutes (200) 1-minute resolution
201 - 209 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution
255 Never stop waiting before motion.

Parameter 13: ON_OFF_BEHAVIOR

Behaviour after after a rapid sequence of BASIC ON and BASIC OFF commands.The intention is to use a much longer timeout value than the time after a single ON command which should then be followed by a short timeout value.The behaviour is almost the same as for parameter 10 (OFF_LOCAL_DISABLE) for values 1-209 - Lamp is switched off and remains so until after a specified timeout once a new motion event (local or remote) is received.
Grösse: 2 Byte, Voreingestellt: 204

Wert Beschreibung
0 Lamp is switched off and remains so until any new motion event (local or remote) is received.
1 - 100 timeout: 1 second (1) to 100 seconds (100) in 1-second resolution
101 - 200 timeout: 1 minute (101) to 100 minutes (200) 1-minute resolution
201 - 209 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution
255 device ignores ON - OFF sequence and uses OFF behavior

Parameter 14: OFF_ON_BEHAVIOUR

Behaviour after after a rapid sequence of BASIC OFF and BASIC ONcommands.The intention is to use a much longer timeout value than the time aftera single OFF command which should then be followed by a shorttimeout value.The behaviour is amost the same as for parameter 11for values 1-209 - Lamp is switched on and remains so until after a specified timeout once a new motion event (local or remote) is received.It then works normally via current motion evaluation.
Grösse: 2 Byte, Voreingestellt: 204

Wert Beschreibung
0 Lamp is switched on and remains so until any new motion event (local or remote) is received. It then works normally via current motion evaluation. Noticeduring the day, this mode cannot be ended remotely due to motion events not being transmittedonly via local motion sensor if enabled.
1 - 100 timeout: 1 second (1) to 100 seconds (100) in 1-second resolution
101 - 200 timeout: 1 minute (101) to 100 minutes (200) 1-minute resolution
201 - 209 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution
255 device ignores OFF - ON sequence and uses ON behaviour

Parameter 15: SEQUENCY_TIME

Time in [ 100 miliseconds ] of maximum delay between BASIC ONand BASIC OFF ( and vice versa ) to consider this as a sequence. It istypically 1 second, but can be exceptionally longer due to retransmissionsand overloadin this case, a longer interval can be allowed ( upto 5 seconds ).
Grösse: 1 Byte, Voreingestellt: 255

Wert Beschreibung
10 - 50 tenth of second

Parameter 16: MOTION_DISABLE

Motion disable timeout after BASIC SET to motion endpoint when theinternal motion sensor is not used for evaluating the behaviour of thelamp and groups 2 and 3. Events are, however, still transmitted to theLifeline, and the lamp can be controlled via remote motion sensors.for values 1-209 - Internal motion sensor is disabled for specified timeout after BASIC SET 0x00 to Motion endpoint.
Grösse: 2 Byte, Voreingestellt: 0

Wert Beschreibung
0 BASIC SET to Motion endpoint ignored, Motion sensor still enabled
1 - 100 timeout: 1 second (1) to 100 seconds (100) in 1-second resolution
101 - 200 timeout: 1 minute (101) to 100 minutes (200) 1-minute resolution
201 - 209 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution
255 timeout: 1 hour (201) to 9 hours (209) in 1-hour resolution

Parameter 2: LIGHT

Light threshold [ lx ]
Grösse: 2 Byte, Voreingestellt: 2000

Wert Beschreibung
0 run Learn ambient light sequence (the level is set automatically)
2 - 1999 lux
2000 2000 - is used as daylight ( always night mode)

Parameter 5: SENSITIVITY

Motion Sensor (radar) Sensitivity [%]Value can be controlled via potentiometerpotentiometer value isused as the default value and any potentiometer movement rewritesthe current setting
Grösse: 1 Byte, Voreingestellt: 100

Wert Beschreibung
2 - 100 %

Parameter 6: BRIGHTNES MEAS INTERVAL

Brightness measuring interval [ minutes ]Interval for ambient light measuring when lamp is on ( lamp switchesoff shortly and measures ). 0=function is off
Grösse: 1 Byte, Voreingestellt: 0

Wert Beschreibung
5 - 120 minutes
0 function is off

Parameter 8: GLOBAL_LIGHT

Use External Ambient Light ValueWhen GLOBAL_LIGHT mode is ONdevice overrides its own lightsensor values and uses Light report values from any Z-Wave lightsensor insteadthis has to be configured appropriately to send lightautomatically.If the last remote light level value is older than 30 minutes, the internallight value is used again until the next external value is received.
Grösse: 1 Byte, Voreingestellt: 1

Wert Beschreibung
0 OFF function
1 ON function

Parameter 9: SLAVE_MODE

Can disable sensor controllStupid mode (bit 2 = 1): - has higher priority then slave mode. - lamp is permanently on (usefull for simple power wall switch controlling).Slave mode ( bit 0 = 1 ):- only if included in Z-Wave network- usefull for controlling via third-party sensor- lamp is directly controlled via Z-Wave, internal sensors are not used for controlling it.Central unit checking ( bit 1 = 1 ):( usefull especialy for controlling via gateway ) When Slave bit is 0:- lamp signalises fail of lifeline connection ( if this bit is zero fail of lifeline connection is not signalised ) When slave bit is 1:- lamp checks presence of Z-Wave device in lifeline group ( gateway ). If it is not present for 2 minutes ( testing repeatedly every 30 seconds ) device switches to normal mode in the same way as after the end of local disabled mode ( ON_BEHAVIOUR )- The device checks every 1 minute for recovery of Lifeline connection.- if no lifeline specified - it works in normal modeBe careful with this option, lamp stops using its own motion sensor in Slave and Stupid mode.
Grösse: 1 Byte, Voreingestellt: 2

Wert Beschreibung
0 Normal mode
1 Slave mode without gateway checking
2 Normal mode with lifeline error signalisation
3 Slave mode with gateway checking
4 "Stupid mode" - lamp permanetly on

Technische Daten

Z-Wave Hardware Platform ZM5202
Gerätetyp On/Off Power Switch
Netzwerkfunktion Always On Slave
Firmware Version HW: 1 FW: 1.00:01.00
Z-Wave Version 6.51.09
Zertifizierungs-ID ZC10-17035489
Z-Wave Produkt Id 0x0271.0x0001.0x1A74
Supported Notification Types Home SecuritySystem
Z-Wave Scene Type Scene
Color White
Sensors LuminanceMotion/No Motion (Binary)
Electric Load Type LED
Firmware Updatable Updatable by Consumer by RF
Outdoor Use ok
Neutral Wire Required ok
Frequenz XXfrequency
Maximale Sendeleistung XXantenna

Unterstützte Kommandoklassen

  • Application Status
  • Association Grp Info
  • Association V2
  • Basic
  • Configuration
  • Device Reset Locally
  • Firmware Update Md V3
  • Manufacturer Specific
  • Multi Channel Association V3
  • Multi Channel V4
  • Node Naming
  • Notification V4
  • Powerlevel
  • Scene Activation
  • Scene Actuator Conf
  • Sensor Multilevel V4
  • Switch All
  • Switch Binary
  • Version V2
  • Zwaveplus Info V2

Gesteuerte Kommandoklassen

  • Basic

Erklärung einiger Z-Wave-Begriffe

  • Controller... ist ein Z-Wave-Gerät mit erweiterten Fähigkeiten zur Verwaltung eines Netzes. Dies sind in der Regel Gateways oder Fernbedienungen. Batteriegespeiste Wandschalter können auch Controller sein.
  • Slave... ist ein Z-Wave-Gerät mit erweiterten Fähigkeiten zur Verwaltung eines Netzes. Es gibt Sensoren, Aktoren und auch Fernbedienungen als Slaves.
  • Primärcontroller (engl. Primary Controller)... ist der zentrale Netzverwalter des Z-Wave-Netzes.
  • Inklusion (eng. Inclusion)... ist der Prozess des Einbindens eines neuen Gerätes ins Z-Wave-Netz.
  • Exklusion (engl. Exclusion)... ist der Prozess des Entfernens eines Gerätes aus dem Z-Wave-Netz.
  • Assoziation (engl. Association)... ist eine Steuerbeziehung zwischen einem steuernden und einem gesteuerten Gerät. Die Information dazu wird im steuernden Gerät in einer Assoziationsgruppe hinterlegt.
  • Wakeup Notifikation (engl. Wakeup Notification) ... ist eine spezielle Funknachricht, mit der ein batteriegespeistes Gerät bekanntmacht, daß es im Aufwachstatus ist und Z-Wave-Nachrichten empfangen kann.
  • Node Information Frame... ist eine spezielle Funknachricht, mit der ein Z-Wave-Gerät seine Geräteeigenschaften bekanntgibt.