Cherubini
META DRY CONTACT SWITCH ZRX
SKU: A510088
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
META Dry Contact Switch 7 can turn ON and OFF equipments with an independent power supply, such as solenoid valves (e.g. gas, water and irrigation), power operated valves etc.In its ZRX variant the device can also be controlled by Cherubini Remote Controls of SKIPPER - POP OR GIRO series.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 8 | |
| 2 | 8 | |
| 3 | 8 | |
| 4 | 8 | |
| 5 | 8 |
Configuration Parameters
Parameter 1: IN_TYPE
Define the input type. (1: button, 2: toggle switch, 0: no switch input) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 10: IN_TOGGLE
Define which event on the input toggle output. (1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up) Size: 1 Byte, Default Value: 15
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 11: IN_ON_EXCLUSION
Define which input event do not switchOn output. (0: none, 1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 12: IN_OFF_EXCLUSION
Define which input event do not switchOff output. (0: none, 1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 21: OUT_TYPE
Define the output type. (0: direct load control or normally Open relay, 1: normally Closed relay) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 23: STARTUP_OUT
Define the output level on startup (0: OFF, 1: ON, 2: Previous status, 3: equal to input) Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 30: TIMER_SETUP
Event that activates timer (0: none, 1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up, 32: Net, 64: sys) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 31: OFF_TIMEOUT
Time in tenth of second after which the output will be switched Off. 0: Off timer disabled Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 32: ON_TIMEOUT
Time in tenth of second after which the output will be switched On. 0: On Timer disabled Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 40: G1_SETUP
Define which input event controls G1group. (0:none, 1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 41: G2_SETUP
Define which input event controls G2group. (0:none, 1: 1 click , 2: 2 clicks, 4: 3 clicks, 8: Hold down, 16: Up) Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 44: G1_ASS_VALUE
The value used to control G1 association group. (0-99: specific value, 100: ON, 101: propagate, 102: toggle remote) Size: 1 Byte, Default Value: 101
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 45: G2_ASS_VALUE
The value used to control G2 association group. (0-99: specific value, 100: ON, 101: propagate, 102: toggle remote) Size: 1 Byte, Default Value: 101
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 50: DIMMING_TIME
Fade On/Off time in second used to control device in dimming group. Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 51: MIN_DIM_LEVEL
Define the minimum dimming level to control device in dimming group. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0 |
Parameter 60: SCENE_SETUP
Define event sent by central scene notification. (0:none, 1:1 click , 2:2 clicks, 4:3 clicks, 8: Hold down, 16: Up) Size: 1 Byte, Default Value: 31
| Setting | Description |
|---|---|
| 0 | 0 |
Technical Data
| Hardware Platform | ZGM130S037HGN2 / ZGM130S037HGN1 |
| Device Type | Binary Switch DT |
| Network Operation | Always On Slave |
| Firmware Version | HW: 01 FW: 07.00 |
| Z-Wave Version | 7.16.3 |
| Certification ID | ZC14-22050108 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |