Quickstart

This is a secure Multilevel Switch DT for XXXQFrequencyName. To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

AD370 is an inwall dimmer module to dim lighting appliances by Z-WaveTM wireless control. It uses MOS technology to achieve both Trailing-edge dimming for LED lighting and Leading-edge dimming for older lamps. Compact in design, yet certified for safety makes it suitable for installation in crammed electrical box located behind wall switches.

Reset to factory default XXXResetDescription
Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5
2 5
3 5

Configuration Parameters

Parameter 1: Switch Type

Def 0
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 10: Calibration Mode

Def 0
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 11: Auto Calibration

Def 1
Size: 2 Byte, Default Value: 1

Setting Description
0 0

Parameter 12: Dimming speed

Def 4, second
Size: 2 Byte, Default Value: 4

Setting Description
0 0

Parameter 13: Set voltage when in 2-wire

Def 230, voltage
Size: 2 Byte, Default Value: 230

Setting Description
0 0

Parameter 14: Use external switch for inclusion and exclusion

Def 1, switch can includ/exculd/reset
Size: 2 Byte, Default Value: 1

Setting Description
0 0

Parameter 15: Lamp type detected

0: unknow, 1 non dimmable, 2 dimmable
Size: 2 Byte, Default Value: 2

Setting Description
0 0

Parameter 16: Wire connection type

0: unknow, 1:2 wire, 2:3 wire
Size: 2 Byte, Default Value: 2

Setting Description
0 0

Parameter 17: Power auto report threshold

Def 0, 0: disable
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 18: Dimming curve

Def 0, 0:linear, 1:log
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 19: Load type detected

Def 0: unknow, 1: Resistive, 2: Capacitive, 3: Inductive
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 2: Auto-on time

Def 0, second
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 3: Auto-off time

Def 0, second
Size: 2 Byte, Default Value: 0

Setting Description
0 0

Parameter 4: Remember last status

Def 1, save last state
Size: 2 Byte, Default Value: 1

Setting Description
0 0

Parameter 5: Interval for wattage/kWh auto report

Def 600, second
Size: 2 Byte, Default Value: 600

Setting Description
0 0

Parameter 6: Report when exceed % change of wattage

Def 25, percent
Size: 2 Byte, Default Value: 25

Setting Description
0 0

Parameter 7: Maximum dimming value

Def 100u0022
Size: 2 Byte, Default Value: 100

Setting Description
0 0

Parameter 8: Minimum dimming value

Def 100
Size: 2 Byte, Default Value: 10

Setting Description
0 0

Parameter 9: MOS operation mode

Def 2
Size: 2 Byte, Default Value: 2

Setting Description
0 0

Technical Data

Hardware Platform ZGM130S037HGN2 / ZGM130S037HGN1
Device Type Multilevel Switch DT
Network Operation Always On Slave
Firmware Version HW: 01 FW: 01.01:00.03
Z-Wave Version 7.16.3
Certification ID ZC14-22020066
Electric Load Type Dimmable ELV (Magnetic)Dimmable LEDIncandescent
Firmware Updatable Updatable by Consumer by RF
Frequency XXfrequency
Maximum transmission power XXantenna
Multilevel Switch DT