Zooz
Zooz 4-in-1 Sensor 700 Series
SKU: ZSE40AU-700
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
PRODUCT FEATURES:- 4 different sensors in 1 smart device: motion, light, temperature, and humidity- Customize your sensor with adjustable motion and reporting settings- NEW 700 Series Z-Wave Chip- SmartStart and S2 Security- Built-in tamper protectionSPECIFICATIONS:- Power: 1 CR123A battery (included)- Wireless Range: Up to 300 feet line of sight- Operating Temperature: 5 - 104F- Weight: 2.0 oz- Dimensions: 2.25" x 2.25" x 1"- Installation: Indoor Use Only
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | The 4-in-1 sensor supports Group 1 with up to five devices for Lifeline communication. |
| 2 | 5 | The 4-in-1 sensor supports Group 2 with up to five devices for basic set reports. |
Configuration Parameters
Parameter 1: Temperature Unit
Use this parameter to switch from Fahrenheit to Celsius scale. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Celsius |
| 1 | Fahrenheit |
Parameter 2: Temperature Reporting Threshold
Use it to set temperature change to be reported by the sensor. Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 50 | where 1 stands for 0.1 degree and 50 stands for 5 degrees |
Parameter 3: Humidity Reporting Threshold
Use it to set humidity change to be reported by the sensor. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 1 - 50 | % |
Parameter 4: Light Reporting Threshold
Use it to set brightness change to be reported by the sensor. Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 5 - 50 | where 5 stands for 5% and 50 stands for 50% |
Parameter 5: Motion Clear Time
Use it to set trigger interval - the time when motion is reported again after initial trigger. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 127 | minutes |
Parameter 6: Motion Sensitivity
Use it to adjust PIR sensor sensitivity. Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 7 | 1 = very high sensitivity and 7 = very low sensitivity |
Parameter 7: LED Mode
Use it to choose between LED indicator modes. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | LED indicator is turned off (no visual notifications). |
| 2 | temperature and motion indicated with flashing light. Flashes every 3 minutes for temperature. |
| 3 | no indication for temperature, motion indicated with red flashing light. |
Parameter 8: Retry Count
Set 0~10 Retry Count, default:3 Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 - 10 | retry count |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 3 FW: 32.32 |
| Z-Wave Version | 7.13.6 |
| Certification ID | ZC12-22040335 |
| Z-Wave Product Id | 0x027A.0x2021.0x2101 |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |