Zooz

Titan Water Valve Actuator

SKU: ZAC36

ZWave+ Security V2

Quickstart

This is a secure Binary Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

PRODUCT HIGHLIGHTS:Automatic shut-off actuator for your main water valveConnect it to your Z-Wave hub for full smart home controlUse it offline with the included leak sensor probeBuilt-in temperature detection for instant freeze detectionRetrofit installation with no tools requiredUse with 1/2 - 1 1/4 ball valves only (close prior to installation)Indoor & outdoor installation with IP66 rating (avoid direct sunlight)NEW 700 series Z-Wave chip for better range and faster controlS2 Security and SmartStart for easier inclusionPRODUCT SPECS:Model Number: ZAC36Z-Wave Signal Frequency: 908.42 MHzPower: 12 V DC (1 A) power supply (included)Temperature Sensor Range: -40 to 257 FSound Indicator: up to 85 dBZ-Wave Range: Up to 400 feet line of sight (up to 130 feet indoors)Operating Temperature: 14-122 F (-10-50 C)Installation and Use: Indoor & outdoor (IP66)Standby Power Consumption: 0.12 WFull Operation Power Consumption: 8.4 W
Reset to factory default XXXResetDescription
Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 (Lifeline Group)- Device Reset Locally Notification- Basic Report- Binary Switch Report- Indicator Report- Sensor Multilevel ReportTemperature Auto report based on Configuration Parameter 0x22 Setting.- Heat Alarm Notification Report (0x04)- 0x00 = State idle- 0x02 = Overheatno location support -- 0x06 = Underheatno location support- Water Alarm Notification Report (0x05)- 0x00 = State idle- 0x02 = Water leak detectedno location support- Water Valve Notification Report (0x0F)- 0x01 = Valve operation0x00 = VALVE CLOSED/OFF (Valve does not let the water run through.)0x01 = VALVE OPEN/ON (Valve lets the water run through)
2 5 - Basic Set (By default the Configuration CC parameter 0x11 (17) Inverse Water Valve report is enabled to send out following report.)- 0x00 = Let the water run through (Based on Configuration Parameter 0x13)- 0xFF = Doesnt let the water run through. (Based on Configuration Parameter 0x12)
3 5 - Basic Set- 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x32 Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x31 Setting)
4 5 Basic SetAlarm- 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x27 Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x26 Setting)
5 5 - Basic Set- 0x00 = IDLE / CANCEL (Based on Configuration Parameter 0x2C Setting)- 0xFF = TRIGGERED (Based on Configuration Parameter 0x2B Setting)

Configuration Parameters

Parameter 17: Water Valve Command and Reporting Behavior

Decide which Z-Wave commands and reports you'd like to use to display when the device is open or closed (or to open / close the device). Default value: 1.
Size: 1 Byte, Default Value: 1

Setting Description
0 reports on when the valve is open (opens the valve when an u0022onu0022 report is sent from the hub), reports off when the valve is closed (closes the valve when an u0022offu0022 report is sent from the hub)
1 - 0 reports off when the valve is open (opens the valve when an u0022offu0022 report is sent from the hub), reports on when the valve is closed (closes the valve when an u0022onu0022 report is sent from the hub)

Parameter 18: Association Group 2 Reports (Open / Close)

Decide which report is sent to Group 2 when parameter 17 is set to value 1 and the valve is closing.
Size: 1 Byte, Default Value: 1

Setting Description
0 reports to Group 2 disabled
1 - 0 Basic Set on (default)
2 - 0 Basic Set off

Parameter 19: Association Group 2 Reports (Open)

Decide which report is sent to Group 2 when parameter 17 is set to value 1 and the valve is opening.
Size: 1 Byte, Default Value: 2

Setting Description
0 reports to Group 2 disabled
1 - 0 Basic Set on
2 - 0 Basic Set off (default)

Parameter 33: Temperature Reporting Unit

Choose which scale you'd like the device to report temperature in.
Size: 1 Byte, Default Value: 2

Setting Description
0 temperature reports disabled
1 - 0 Celsius
2 - 0 Fahrenheit (default)

Parameter 34: Temperature Reporting Threshold

Set the temperature reporting threshold.
Size: 2 Byte, Default Value: 260

Setting Description
0 - 511 degrees

Parameter 35: Temperature Report Offset

Set the temperature reporting offset
Size: 2 Byte, Default Value: 256

Setting Description
0 - 4607 degrees

Parameter 36: Overheat Trigger Value

Set the overheat alarm trigger value. Default: 104.
Size: 2 Byte, Default Value: 360

Setting Description
0 - 511 degrees

Parameter 37: Overheat Recover value

Set the overheat alarm cancellation trigger value. Default: 86.
Size: 2 Byte, Default Value: 342

Setting Description
0 - 511 degrees

Parameter 38: Association Group 4 Overheat Trigger

Decide which report is sent to Group 4 when the overheat alarm (set in parameter 36) is triggered.
Size: 1 Byte, Default Value: 0

Setting Description
0 reports to Group 4 disabled (default)
1 - 0 Basic Set on
2 - 0 Basic Set off

Parameter 39: Association Group 4 Overheat Cancel

Decide which report is sent to Group 4 when the overheat alarm is cancelled.
Size: 1 Byte, Default Value: 0

Setting Description
0 reports to Group 4 disabled (default)
1 - 0 Basic Set on
2 - 0 Basic Set off

Parameter 40: Freeze Trigger Value

Set the freeze alarm trigger value.
Size: 2 Byte, Default Value: 288

Setting Description
0 - 511 degrees

Parameter 41: Freeze Recover Value

Set the freeze alarm cancellation trigger value. Default: 36.
Size: 2 Byte, Default Value: 292

Setting Description
0 - 511 degrees

Parameter 42: Freeze Alarm Operation Mode

Decide if you want to allow the valve actuator to open and close during freeze alarm mode. If the actuator is disabled, it won't react to Z-Wave or manual triggers to open or close until the freeze alarm is cleared.
Size: 1 Byte, Default Value: 1

Setting Description
0 operation disabled
1 - 0 operation enabled (default)

Parameter 43: Association Group 5 Freeze Trigger

Decide which report is sent to Group 5 when the freeze alarm (set in parameter 40) is triggered.
Size: 1 Byte, Default Value: 0

Setting Description
0 reports to Group 5 disabled (default)
1 - 0 Basic Set on
2 - 0 Basic Set off

Parameter 44: Association Group 5 Freeze Cancel

Decide which report is sent to Group 5 when the freeze alarm is cancelled.
Size: 1 Byte, Default Value: 0

Setting Description
0 reports to Group 5 disabled (default)
1 - 0 Basic Set on
2 - 0 Basic Set off

Parameter 49: Association Group 3 Water Leak Trigger

Decide which report is sent to Group 3 when a leak alarm is triggered (from the connected leak detection probe).Values:
Size: 1 Byte, Default Value: 1

Setting Description
0 reports to Group 3 disabled
1 - 0 Basic Set on (default)
2 - 0 Basic Set off

Parameter 50: Association Group 3 Water Leak Cancel

Decide which report is sent to Group 3 when the leak alarm is cleared (water is no longer detected by the connected probe).
Size: 1 Byte, Default Value: 0

Setting Description
0 reports to Group 3 disabled (default)
1 - 0 Basic Set on
2 - 0 Basic Set off
2 - 0 Basic Set off
2 - 0 Basic Set off

Parameter 51: Water Leak Detection Valve Control

Decide if you want to allow the valve actuator to open and close during a leak alarm event. If the actuator is disabled, it won't react to Z-Wave or manual triggers to open or close until the leak alarm is cleared.
Size: 1 Byte, Default Value: 1

Setting Description
0 operation disabled
1 - 0 operation enabled (default)

Parameter 65: Buzzer

Decide if you'd like to receive sound (beep) feedback when operating the actuator as well as sound alarms for different modes and alarms the actuator goes into when installed.
Size: 1 Byte, Default Value: 1

Setting Description
0 sound notifications disabled
1 - 0 sound notifications enabled (default)

Parameter 66: LED Brightness Level

Decide how bright you'd like the LED indicator to be on your actuator. If you set it to value 0, the LED indicator will be disabled. Default: 80.
Size: 1 Byte, Default Value: 80

Setting Description
0 - 99 %

Parameter 67: Z-Wave Button Lock Protection

Enable Z-Wave button lock protection if you'd like to prevent the Z-Wave button from being locked accidentally.
Size: 1 Byte, Default Value: 0

Setting Description
0 Z-Wave button lock disabled (default)
1 - 0 Z-Wave button lock enabled

Parameter 81: Notification Report

Configure Notification Report (Bitmask)
Size: 1 Byte, Default Value: 13

Setting Description
0 WaterValve Open / Close Disabled / Enabled
5 - 0 Overheat Detection Disabled / Enabled
10 - 0 Freeze Detection Disabled / Enabled
13 - 0 All enabled
15 - 0 Wired Leak Probe Detection Disabled / Enabled

Technical Data

Hardware Platform ZGM130
Device Type Binary Switch
Network Operation Always On Slave
Firmware Version HW: 3 FW: 3.03
Z-Wave Version 7.13.2
Certification ID ZC12-22010332
Z-Wave Product Id 0x027A.0x0101.0x0036
Frequency XXfrequency
Maximum transmission power XXantenna
Binary Switch