Vision
4 in 1 PIR Sensor
SKU: ZP3113BR-7
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
* Includes Motion, Temperature, Humidity, and Light sensor* 360-degree detection (suitable for ceiling fixture)* Compact Size: 59*59*41mm* 1 x CR123Battery* Low Battery Detection* LED Status Indicator* 100feet line of sight
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1 = Lifeline (Battery, Reset Locally, Indicator, Notification) |
| 2 | 5 | Group 2 = ON/OFF Control (Basic Set) |
Configuration Parameters
Parameter 1: Temperature Unit Selection
0x00 = C0x01 = F Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Choose F |
| 0 | Choose C |
Parameter 2: Auto Temperature Report Interval
1~50 (Set up from 0.1C~5C) Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 50 | Auto Temperature Interval from 0.1C~5C |
Parameter 3: Auto Humidity Report Interval
1~50 (Set up from 1%~50%) Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 1 - 50 | Auto Humidity Report Interval from 1% ~ 50% |
Parameter 4: Auto Light Report Interval
0,5~50 (Set up from 0 for Off or 5%~50%) Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 50 | Auto Light Report Interval from off or 5%~50% |
Parameter 5: Motion Re-triggering Duration
1 ~ 127 (unsigned decimal) Minutes(default: 3 minutes) Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 127 | Motion Re-triggering Duration (in 1 ~ 127 minutes) |
Parameter 6: Motion Sensitivity
1 ~ 7(default: 4) Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 7 | Motion Sensitivity from level 1 ~ level 7 |
Parameter 7: LED Flash Mode Selection
1 ~ 3 (Mode 1 ~ Mode 3)Mode 1: LED Turn Off (Both Temp/PIR Trigger)Mode 2: LED Quick Flash (Temp. / PIR Trigger)Mode 3: PIR Trigger (Quick Flash)Temp. Trigger (LED Off) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 3 | LED Flash Mode Selection |
Parameter 8: PIR Trigger Notification Re-sending Times
0 ~ 10 (unsigned decimal) Times(default: 3 Times) Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 - 10 | PIR Trigger Notification Re-sending Times from 0 time to 10 times |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 3 FW: 32.32 |
| Z-Wave Version | 7.13.6 |
| Certification ID | ZC12-21100319 |
| Z-Wave Product Id | 0x0109.0x2021.0x2112 |
| Firmware Updatable | Not Updatable |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |