Zooz
Water Sensor
SKU: ZSE42
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
PRODUCT HIGHLIGHTS:- Quick and reliable water leak alerts sent to your Z-Wave hub- NEW 700 series chip for faster communication and more battery life than ever- Extra small to fit anywhere- Powered by a long-lasting single coin battery- The latest S2 security and SmartStart for secure set-up- Supports OTA firmware updatesPRODUCT SPECS:- Model Number: ZSE42- Power: 1 x CR2032 battery- Operating Temperature: 32104 F- Dimensions: 1.9 x 1 x 0.3- Range: Up to 130 feet line of sight - Installation and Use: Indoor or outdoor under eve (cant be exposed to direct rainfall or sun, a little splash is OK)
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 3 | Lifeline. Notification sent back to the hub when a leak is detected and when it's cleared. |
| 2 | 5 | This device will send a Basic Set command to Group 2 whenever it detects water. The value of the basic set command sent to Group 2 can be adjusted in the advanced settings to customize the sensors behavior. |
Configuration Parameters
Parameter 1: LED Indicator Mode
Choose whether you'd like the LED indicator to light up when water is detected. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED indicator doesn't light up when water is detected |
| 1 | LED indicator lights up when water is detected |
Parameter 2: Alarm Clear Delay
Set the delay for a u0022dryu0022 report to be sent to the hub when water is no longer detected. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 3600 | seconds |
Parameter 3: Battery Reporting Threshold
Set the battery reporting threshold. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 1 - 50 | % |
Parameter 4: Low Battery Alert
Set the battery level for a low battery alert to be sent to the hub. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 10 - 50 | % |
Parameter 5: Group 2 ON/OFF Basic Set Commands
Choose when you'd like the sensor to send on/off basic set commands to Group 2 once the water detection status changes. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Doesn't send basic set commands |
| 1 | Sends 0xFF (ON) when water is detected and 0x00 (OFF) when water is no longer detected |
| 2 | Sends 0x00 (OFF) when water is detected and 0xFF (ON) when water is no longer detected |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 7.13.9 |
| Certification ID | ZC12-21080294 |
| Z-Wave Product Id | 0x027A.0x7000.0xE002 |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | Blue |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |