HomeSeer
Smart In Wall Dimmer
SKU: HS-WX300
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
HS-WX300 is a Z-Wave in-wall light switch that may be configured to operate as either a dimmer switch or an on/off switch. It may be installed with or without a neutral wire and it works with both wired and wireless companion switches in 3-way circuit configurations. This switch has been designed, tested and certified for use in the United States and Canada.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1 is for lifeline communication |
| 2 | 5 | Group 2 supports Basic Set, refer to your controller manual for instructions on setting up these features. |
Configuration Parameters
Parameter 11: Set dimmer Ramp rate for remote control
Possible values: 0-900=No delay (instant ON), 1=1 second Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 - 90 | Possible values: 0-90 0=No delay (instant ON), 1=1 second |
Parameter 12: Set dimmer Ramp rate for local control
Possible values: 0-90 0=No delay (instant ON), 1=1 second Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 - 90 | Possible values: 0-90 0=No delay (instant ON), 1=1 second |
Parameter 13: Sets the display mode of the LEDs
0=Normal mode (LEDs show load status)1=Status mode (custom LED status) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0=Normal mode (LEDs show load status) 1=Status mode (custom LED status) |
Parameter 14: Sets the Normal display mode LED color
Possible values: 0-60=White, 1=Red, 2=Green, 3=Blue,4=Magenta, 5=Yellow, 6=Cyan Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 6 | Possible values: 0-6 0=White, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan |
Parameter 21: Sets the Status mode LED 1 (bottom) color
Possible values: 0-70=Off, 1=Red, 2=Green, 3=Blue,4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 22: Sets the Status mode LED 2 color
Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 23: Sets the Status mode LED 3 color
Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 24: Sets the Status mode LED 4 color
Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 25: Sets the Status mode LED 5 color
Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 26: Sets the Status mode LED 6 color
Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 27: Sets the Status mode LED 7 (top) color
Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 7 | Possible values: 0-7 0=Off, 1=Red, 2=Green, 3=Blue, 4=Magenta, 5=Yellow, 6=Cyan, 7=White |
Parameter 3: LED Light Mode
Sets bottom LED operation (in normal mode) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | 0 = all LED ON if load is OFF 1 = all LED OFF if load is OFF |
Parameter 30: LED Blink Frequency
Sets the dimmer Blink frequencyfor All LEDs in Status modePossible values: 0, 1-2550=No blink, 1=100ms ON then 100msOFF Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 255 | Possible values: 0, 1-255 0=No blink, 1=100ms ON then 100ms OFF |
Parameter 31: Enable LED Blink
Sets LED(s) 1-7 to Blink in StatusmodeBitmask defines specific LEDs to enablefor blinking:Note: this decimal value is derived froma hex code calculationbased on the following:Bit 0 = led 1, Bit 1 = led 2, Bit 2 = led 3,Bit 3 = led 4, Bit 4 = led 5,Bit 5 = led 6, Bit 6 = led 7IE: value of 1 = first LED, 64 = led 7 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 127 | Bitmask defines specific LEDs to enable for blinking: Note: this decimal value is derived from a hex code calculation based on the following: Bit 0 = led 1, Bit 1 = led 2, Bit 2 = led 3, Bit 3 = led 4, Bit 4 = led 5, Bit 5 = led 6, Bit 6 = led 7 IE: value of 1 = first LED, 64 = led 7 |
Parameter 32: No Neutral Mode
Sets the Wire mode / no neutralmod of the switch0 = 3 wire mode (Neutral, Line, & Load)1 = 2 wire mode (Line & Load) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0 = 3 wire mode (Neutral, Line, & Load) 1 = 2 wire mode (Line & Load) |
Parameter 4: Invert Buttons
Sets paddles load orientation Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0 = Top of Paddle turns load ON 1 = Bottom of Paddle turns load ON |
Parameter 5: Sets the lowest dimming threshold
Possible values: 1-143-wire mode (1=16%, 14=25%)2-wire mode (1=25%, 14=30%) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 14 | Possible values: 1-14 3-wire mode (1=16%, 14=25%) 2-wire mode (1=25%, 14=30%) |
Parameter 6: Enables/Disables Central Scene and multiple tap functions
0 = Central Scene Enabled, controlsload with delay. Enables Multi-tap andpress and hold1 = Central Scene Disabled, controlsload instantly. Disables multi-tap,central scene, press and hold Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0 = Central Scene Enabled, controls load with delay. Enables Multi-tap and press and hold 1 = Central Scene Disabled, controls load instantly. Disables multi-tap, central scene, press and hold |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Multilevel Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.11 |
| Z-Wave Version | 7.15.2 |
| Certification ID | ZC12-21070246 |
| Z-Wave Product Id | 0x000C.0x4447.0x4036 |
| Color | White |
| Neutral Wire Required | ok |
| Z-Wave Scene Type | Scene & Central Scene |
| Firmware Updatable | Updatable by Consumer by RF |
| Electric Load Type | Dimmable FluorescentDimmable LEDFluorescentIncandescentLED |
| Outdoor Use | ok |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |