Philio
2 Wire Dimmer
SKU: PAD15-ANZ
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The device should only need two wires for dimming, easy to install. This device is a security enabled Z-Wave Plus product that uses encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products. Z-Wave enabled devices displaying the Z-Wave logo can also be used with this device regardless of the manufacturer, and this device can also be used in other manufacturers Z-Wave enabled networks.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | 1. Grouping 1 Lifeline (Maximum 5 nodes). 2. MULTILEVEL_SWITCH_REPORT When on or ostate has been changed, it will send Multilevel SwitchReport to the nodes of Grouping 1. 3. NOTIFICATION_REPORT When overload occurred. 4. DEVICE_RESET_LOCALLY_NOTIFICATION When PAD15 isreset manually, it will send DEVICE_RESET_LOCALLY_NOTIFICATION to the nodes of group 1. |
Configuration Parameters
Parameter 1: Switch set
To select connected switch function.Setting value:0: Only S1 is effective1: Both S1 and S2 are effective.2: S1 dimmer upS2 dimmer down Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0: Only S1 is e ective |
| 1 | 1: Both S1 and S2 are e ective. |
| 2 | 2: S1 dimmer up S2 dimmer down |
Parameter 2: Power-on recovery status set
To set dimmer level when AC power on.Setting value:0: OFF-0%1: ON-last level2: ON-100% Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0: OFF-0% |
| 1 | 1: ON-last level |
| 2 | 2: ON-100% |
Parameter 3: RF report set
To set if device send Multilevel Switch report to gateway when dimming finished.Setting value:1: report ON0: report OFF Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | 0: report OFF |
| 1 | 1: report ON |
Parameter 4: Maximum level
To set dimming level maximum value. Dimming level will not over the setting value. Setting value:Cannot be lower than the Minimum level Size: 1 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 1 - 99 | 1~99 : 1% ~ 99% |
Parameter 5: Minimum level
To set dimming level minimum value. Dimming level will directly go to 0% when dimming value is lower than the setting value.Setting value:Cannot be higher than the Maximum level Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 98 | 0~98 : 0% ~ 98% |
Parameter 6: Basic duration set
Unit: secondTo set dimming finished duration time when physical switch used.Ex: When setting is 2, it will take 2 seconds from switch on action to dimming finished. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 - 127 | Unit: second ,0 ~127second |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Multilevel Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.01 |
| Z-Wave Version | 7.13.5 |
| Certification ID | ZC12-21070243 |
| Z-Wave Product Id | 0x013C.0x0005.0x007e |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |