This is a
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Heighten your senses with the Jasco Z-Wave Plus Flood/Freeze with Humidity Sensor. When paired with a compatible hub, the smart sensor provides notification when water levels or temperatures change. Z-Wave devices can also be activated wirelessly for increased convenience and peace of mind. Your automation possibilities are seemingly infinite when connected to a compatible hub. Trigger eventsThe sensor communicates with your hub to initiate desired actions of Z-Wave devices. Increase peace of mind by automatically turning on lights, sending a notification to your phone, activating an alarm or more when temperatures, humidity or water levels change. Detection alarmBuilt-in speaker emits audible alert when water levels or temperatures change to allow immediate action by anyone in the area. Dual functionBase contacts and a detachable probe accommodate various setups. Recessed contacts on the base of the sensor are ideal for placement on flat surfaces. The included probe extends reach for use in wells, sump pump holes and other small spaces. Temperature and humidity sensorIn humid or temperature-sensitive spaces, protect against costly damage caused by freezing or overheating. Indicator lightLED indicator displays status and provides feedback during programming. It also serves as notification if tampering with the sensor occurs. Universal compatibilityZ-Wave Plus and all previous Z-Wave generations work together to allow continued expansion of your home-automation network.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Supports Device Reset Locally and receives unsolicited status updates. |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Alternative way to perform Exclusion Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Not engaged |
1 | Alternate Exclusion |
Detection Mode (1:wet 2:Dry) Size: 2 Byte, Default Value: 1
Setting | Description |
---|---|
1 | 1: Wet |
2 | 2: Dry |
Set Temp Report Freq. Size: 2 Byte, Default Value: 60
Setting | Description |
---|---|
5 - 1440 | Set Temp Report Freq. |
Set Battery Report Freq. Size: 2 Byte, Default Value: 1440
Setting | Description |
---|---|
5 - 1440 | Set Battery Report Freq. |
Set Low Temp Level Size: 2 Byte, Default Value: 33
Setting | Description |
---|---|
0 - 122 | Low Temp |
Set High Temp Level Size: 2 Byte, Default Value: 104
Setting | Description |
---|---|
0 - 122 | High temp |
Set Temp Report Freq. Size: 2 Byte, Default Value: 60
Setting | Description |
---|---|
5 - 360 | 5.... 360 Minutes - Sent every 5 minutes, up to 6 hours |
60 | Hourly |
0 = no LED, no beep (Default)1 = Red LED Flash 5x, no beep2 = Red LED cont flash, no beep3 = no LED, cont beep4 = Red LED cont flash, cont beep Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | No LED, No Beep |
1 | Red LED Flash 5x, no beep |
2 | Red LED continuous flash, no beep |
3 | No LED, continuous beep |
4 | Red LED continuous flash, continuous beep |
Hardware Platform | ZGM130 |
Device Type | Notification Sensor |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 7.04 |
Z-Wave Version | 7.13.6 |
Certification ID | ZC12-21060242 |
Z-Wave Product Id | 0x0063.0x4953.0x3432 |
Firmware Updatable | Updatable by Consumer by RF |
Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |