This is a
FEATURES:- Manual or Z-Wave on/off control with instant status updates- NEW: 700 series Z-Wave chip for better range and faster control- Simple Direct 3-Way: connect with existing on/off switches in 3-way, 4-way, and 5-way set-ups, no add-on needed- Scene control: trigger actions with multi-tap (select hubs only)- Smart bulb mode: disable relay and control the light via Z-Wave- Remembers and restores on/off status after power failure- NEW: discreet LED indicator for easy set-up and troubleshooting- Works with LED and incandescent bulbs (dont use with tubes)
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 3 | Lifeline communication with the primary controller with basic reports. |
2 | 5 | Basic set commands for on/off control of other Z-Wave devices in the network. |
Choose if you want to turn the light on or turn the light off when you toggle up the switch. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Toggle up turns the light on, toggle down turns it off (default) |
1 | Toggle up turns the light off, toggle down turns it on |
2 | Toggle any direction to turn the light on/off (change state) |
Enable or disable scene control functionality for quick double tap triggers. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | scene control disabled (default) |
1 | scene control enabled |
Set reporting behavior for disabled physical control. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | switch reports on/off status and change LED indicator state even if physical and Z-Wave control is disabled (default). |
1 | switch doesn't report on/off status or change LED indicator state when physical (and Z-Wave) control is disabled. |
Choose how the switch reports its status back to the hub. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Binary switch report for Z-Wave control, basic set report for toggle (physical) control |
1 | binary switch report for both Z-Wave and toggle control (default) |
Choose how to use the LED indicator. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | LED indicator is on when switch is off, LED indicator is off when switch is on (default) |
1 | LED indicator is on when switch is on, LED indicator is off when switch is off |
2 | LED indicator is always OFF |
3 | LED indicator is always ON |
Use this parameter to enable or disable the auto turn-off timer function (the time after which you want the switch to automatically turn off once it has been turned on). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | timer disabled |
1 - 65535 | minutes |
Use this parameter to enable or disable the auto turn-on timer function (the time after which you want the switch to automatically turn on once it has been turned off). Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | timer disabled |
1 - 65535 | minutes |
Set the on off status for the switch after power failure. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | forced to OFF (regardless of state prior to power outage |
1 | forced to ON (regardless of state prior to power outage) |
2 | remembers and restores on/off status after power failure (default) |
Hardware Platform | ZGM130 |
Device Type | Binary Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.00 |
Z-Wave Version | 7.13.6 |
Certification ID | ZC12-21050228 |
Z-Wave Product Id | 0x027A.0x7000.0xA003 |
Firmware Updatable | Updatable by Consumer by RF |
Neutral Wire Required | ok |
Color | White |
Electric Load Type | IncandescentLED |
Z-Wave Scene Type | Central Scene |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |