Minoston

Smart On/Off Toggle Switch

SKU: MS12ZS

ZWave+ Security V2

Quickstart

This is a secure Binary Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

In-Wall Smart Switch design features a housing depth that is up to 20 percent smaller than the previous Z-Wave models. This reduced size coupled with the elimination of heat taps provides a better fit in older style boxes and multi-gang configurations. SimpleWire technology allows line and load to automatically be configured with auto-sensing line-load terminals. All of this is coupled with Z-Wave S2 and SmartStart allows for effortless installation while being safer than ever!
Reset to factory default XXXResetDescription
Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Z-Wave Lifeline
2 5 Send BASIC SET COMMAND
3 5 Send BASIC SET COMMAND

Configuration Parameters

Parameter 1: KeyFunction

Parameter=1Size=1Value=0 Up Button: On Down Button: OffValue=1 Up Button: Off Down Button: On Value=2 Up Button: On/OffDown Button: On/Off
Size: 1 Byte, Default Value: 0

Setting Description
0 Up Button ON,Down Button OFF
1 Up Button OFF,Down Button ON
2 Up Button ON/OFF,Down Button ON/OFF

Parameter 11: Enable or Disable OutPut control

Parameter=11Size=1Value=0 disable local button and External Switch controlenable Z-Wave controlValue=1enable local button and External Switch controlenable Z-Wave controlValue = 2disable local button and External Switch control
Size: 1 Byte, Default Value: 1

Setting Description
0 disable local button and External Switch control enable Z-Wave conrol
1 enable local button and External Switch control enable Z-Wave control
2 disable local button and External Switch control

Parameter 12: external switch type

Parameter=12, Size=1, Value=0 toggle switch(device changes status when switch changesstatus)(default);Value=1 momentary switch
Size: 1 Byte, Default Value: 0

Setting Description
0 toggle switch (device changes status when switch changes status)
1 momentary switch

Parameter 13: Behavior when Output control disabled

Parameter 13 Size=1Value=0 report on/off status and change LED indicator when upperor lower paddle is pressed and Parameter 11 is set to value 0 or 2 (output control disabled).Value=1 DONt report on/off status or change LED indicator when upperor lower paddle is pressed and Parameter 11 is set to value 0 or 2 (output control disabled).Default = 0
Size: 1 Byte, Default Value: 0

Setting Description
0 report on/off status and change LED indicator when upperor lower paddle is pressed and Parameter 11 is set to value 0 or 2 (output control disabled)
1 DONt report on/off status or change LED indicator when upperor lower paddle is pressed and Parameter 11 is set to value 0 or 2 (output control disabled).

Parameter 14: LED Indicator Color

Parameter=14Size=1Value=0 WhiteValue=1BlueValue=2GreenValue=3Red
Size: 1 Byte, Default Value: 1

Setting Description
0 White
1 Blue
2 Green
3 Red

Parameter 15: LED Indicator Brightness

Parameter=15Size=1Value=0 Bright (100%)Value=1Medium (60%) Value=2Low (30%)
Size: 1 Byte, Default Value: 1

Setting Description
0 Bright (100%)
1 Medium (60%)
2 Low (30%)

Parameter 16: Association reports

Parameter=16Size=1Values:0Z-WavecontrolBinary switch reportManualcontrol:Basic setreport1Z-WavecontrolBinary switch reportManualcontrol: Binary switch report
Size: 1 Byte, Default Value: 1

Setting Description
0 Z-WavecontrolBinary switch report Manualcontrol:Basic setreport
1 Z-WavecontrolBinary switch report Manualcontrol: Binary switch report

Parameter 2: LED Indicator

Parameter=2Size=1Value=0 On when Off and Off when OnValue=1On when On and Off when Off Value=2Always Off Value=3Always On
Size: 1 Byte, Default Value: 0

Setting Description
0 On when Off and Off when On
1 On when On and Off when Off
2 Always OFF
3 Always ON

Parameter 3: Auto Turn-Off Timer

Parameter=3Size=4Value=0timer disabled (default); Values: 165535 (minutes);
Size: 4 Byte, Default Value: 0

Setting Description
0 - 65535 Auto Turn-Off Timer

Parameter 5: Auto Turn-On Timer

Parameter=5Size=1Value=0timer disabled (default);Values: 165535 (minutes);
Size: 4 Byte, Default Value: 0

Setting Description
0 - 65535 Auto Turn-On Timer

Parameter 8: Restores state after power failure

Parameter=8Size=1Value=0 output offValue=1 output on Value=2out put the state after power
Size: 1 Byte, Default Value: 2

Setting Description
0 Output OFF
1 Output ON
2 out put the state after power

Parameter 9: Enable or Disable Scene

Parameter=9Size=1Value=0 disable Value=1 enable
Size: 1 Byte, Default Value: 0

Setting Description
0 disable
1 enable

Technical Data

Hardware Platform ZGM130
Device Type Binary Switch
Network Operation Always On Slave
Firmware Version HW: 1 FW: 1.00
Z-Wave Version 7.13.6
Certification ID ZC12-21040211
Z-Wave Product Id 0x0312.0xEE00.0xEE03
Color White
Switch Type Toggle
Firmware Updatable Updatable by Consumer by RF
Frequency XXfrequency
Maximum transmission power XXantenna
Binary Switch