Evaloigk
S2 Remote Control Switch
SKU: ZW922
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Custom lighting control is at your fingertips with theZ-Wave 2-Button Portable Hub Remote. This versatile remote communicates with your hub to activate up to 6 unique, lighting scenes. Once the remote is connected to your existing network, you can begin programming the lights to personalize your indoor space. The wireless lighting control has an overall signal range of up to 150 feet and is compatible with any device that works with your hub.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Lifeline |
| 2 | 5 | supports Basic Set and is controlled by pressing the UP or Down button once |
| 3 | 5 | Holding down the key supports sending multilevel dimming |
Configuration Parameters
Parameter 1: LED Indicator Mode
Paramter No: 1(0x01) Size:1 Byte (default=1) Value: 00 LED always off Value: 01 LED normal mode Value: 02 LED always on in color specified in Parameter 2 Value: 03 LED always on in color specified in Parameter 3 Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED always off |
| 1 | LED normal mode |
| 2 | LED always on in color specified in Parameter 2 |
| 3 | LED always on in color specified in Parameter 3 |
Parameter 2: LED Indicator Color for Upper paddle remote cont
Paramter No: 2(0x02) Size:1 Byte (default=1) Value: 00 White Value: 01 Blue Value: 02 Green Value: 03 Red Value: 04 Magenta Value: 05 Yellow Value: 06 Cyan Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | White |
| 1 | Blue |
| 2 | Green |
| 3 | Red |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
Parameter 3: LED Indicator Color for Lower paddle remote cont
Paramter No: 3(0x03) Size=1 Byte(default=0) Value: 00 White Value: 01 Blue Value: 02 Green Value: 03 Red Value: 04 Magenta Value: 05 Yellow Value: 06 Cyan Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | White |
| 1 | Blue |
| 2 | Green |
| 3 | Red |
| 4 | Magenta |
| 5 | Yellow |
| 6 | Cyan |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Central Scene Device |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 7.13.6 |
| Certification ID | ZC12-21020180 |
| Z-Wave Product Id | 0x0312.0x7000.0xF001 |
| Z-Wave Scene Type | Central Scene |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |