Evaloigk
Z-Wave Mutil-relay
SKU: ZW12
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This product is a multi-channel Z-Wave breaker with built-in S2 security.Built-in high-power relay, multi-type external switch selection.Very convenient.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Lifeline |
| 2 | 5 | Send on/off control |
| 3 | 5 | Send on/off control |
Configuration Parameters
Parameter 1: Restore state after power failure
Restore state after power failure: always off, always on or follow the status before power failure Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | All relays automatically turn OFF once power is restored |
| 1 | All relays remember the status prior to power outage and turns back to it |
| 2 | All relays turned on after power failure |
| 3 | R1 recovered, R2 ON |
| 4 | R2 recovered, R1ON |
Parameter 10: Input 1 trigerring
Connect input and output or separate the output from the input for switch 1 Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | trigger disable (only notification to hub according to set par 2) |
| 1 | trigger unable (default); trigger the relay and hub notification |
Parameter 11: Input 2 trigerring
Connect input and output or separate the output from the input for switch 2 Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | trigger disable (only notification to hub according to set par 2) |
| 1 | trigger unable (default); trigger the relay and hub notification |
Parameter 12: EP1 Manual Control
User can set it to disable the output for switch one Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | manual control disabled (no reports to the hub) |
| 1 | manual control enabled |
| 2 | manual control disabled (sends on/off reports to the hub) |
Parameter 13: EP2 Manual Control
User can set it to disable the output for switch two Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | manual control disabled (no reports to the hub) |
| 1 | manual control enabled |
| 2 | manual control disabled (sends on/off reports to the hub) |
Parameter 15: EP1 Auto Turn-Off Timer Unit
Setting auto off timer unit(minutes, seconds or hours) for relay one Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | minutes |
| 1 | seconds |
| 2 | hours |
Parameter 16: EP1 Auto Turn-ON Timer Unit
Setting auto on timer unit(minutes, seconds or hours) for relay one Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | minutes |
| 1 | seconds |
| 2 | hours |
Parameter 17: EP2 Auto Turn-Off Timer Unit
Setting auto off timer unit(minutes, seconds or hours) for relay two Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | minutes |
| 1 | seconds |
| 2 | hours |
Parameter 18: EP2 Auto Turn-ON Timer Unit
Setting auto on timer unit(minutes, seconds or hours) for relay two Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | minutes |
| 1 | seconds |
| 2 | hours |
Parameter 2: Select switch one's type
Select switch one's type: switch or sensor Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | momentary switch |
| 1 | toggle switch (contact closed -ON, contact opened - OFF) |
| 2 | toggle switch (device changes status when switch changes status) |
| 3 | garage door mode(toggle switch type for external switch (like in value 1) + built-in 2 second auto-off timer for Z-Wave control (so if user turns the relay on from the Z-Wave hub, it will automatically turn off after 2 seconds) |
| 4 | water alarm |
| 5 | heat alarm |
| 6 | Smoke alarm |
| 7 | Door alarm |
| 8 | CO alarm |
| 9 | CO2 alarm |
Parameter 24: Sw1,Sw2 setting
DC motor mode: sync R1 and R2 together to prevent them from being activated at the same time Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Normal |
| 1 | Union (only switch type1 < 4 && switch type2 < 4) IF both switches OFF - only one of them may be turned ON. - turning sw1 ON : delayed 0.5 s, sw2 and R2 turned off first (immediately) - turning sw2 ON - delayed 0.5s , sw1and R1 turned off first ( immediately ) The situation for DC motor control(SW1 controlright, SW2 control-left. -main switch can turn ON and OFF only sw1 |
Parameter 3: Select switch two's type
Select switch two's type: switch or sensor Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | momentary switch |
| 1 | toggle switch (contact closed -ON, contact opened - OFF) |
| 2 | toggle switch (device changes status when switch changes status) |
| 3 | garage door mode(toggle switch type for external switch (like in value 1) + built-in 2 second auto-off timer for Z-Wave control (so if user turns the relay on from the Z-Wave hub, it will automatically turn off after 2 seconds) |
| 4 | water alarm |
| 5 | heat alarm |
| 6 | Smoke alarm |
| 7 | Door alarm |
| 8 | CO alarm |
| 9 | CO2 alarm |
Parameter 5: LED indicator
Indicator inverse, follow, always on or always off Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | LED on when relay off, LED off when relay on |
| 1 | LED on when relay on, LED off when relay off |
| 2 | LED Always OFF |
| 3 | LED Always ON |
Parameter 6: EP1 Auto Turn-off Timer
Setting auto off timer value for relay one Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | EP1 Auto Turn-off Timer |
Parameter 7: EP1 Auto Turn-on Timer
Setting auto on timer value for relay one Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | EP1 Auto Turn-on Timer |
Parameter 8: EP2 Auto Turn-off Timer
Setting auto off timer value for relay two Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | EP2 Auto Turn-off Timer |
Parameter 9: EP2 Auto Turn-on Timer
Setting auto on timer value for relay two Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 65535 | EP2 Auto Turn-on Timer |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Binary Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 7.13.6 |
| Certification ID | ZC12-21020174 |
| Z-Wave Product Id | 0x0312.0xBB00.0xBB0A |
| Firmware Updatable | Updatable by Consumer by RF |
| Switch Type | Push Button |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |