Heatit controls
Heatit ZM Single Relay 16A
SKU: ZM Single Relay 16A
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Heatit ZM Single Relay is a high power relay for in-wall installations.The relay allows you to control connected devices either through your Z-Wave network or via a wired switch. The module is equipped with a 16A relay and has a scene controller functionality.The device can withstand a load of max 16A /3600W at 230VAC.The Heatit ZM Single Relay has a power metering feature that allows you to monitor the power consumption of your connected devices.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline. (Normally used by the Z-Wave Controller) Sends: |
| 2 | 5 | Send Basic Set commands representing the status of the internal relay when changed from S1.(0x00, 0xFF) ON/OFF |
| 3 | 5 | When S1 pressed/heldPress: 0x00, 0xFFHeld: Multilevel Switch Start Level Change CommandLevel Increase Start / Level Increase StopLevel Decrease Start / Level Decrease Stop |
| 4 | 5 | - Basic Set (S2)(0x00, 0xFF) |
| 5 | 5 | When S2 pressed/heldPress: 0x00 / 0xFFHeld: Multilevel Switch Start Level Change CommandLevel Increase Start / Level Increase StopLevel Decrease Start / Level Decrease StopMax nodes in group: 5 |
Configuration Parameters
Parameter 1: Load limit
Ensures that the device does not draw more current than rated. Immunity for power consumption peaks. Size: 1 Byte, Default Value: 16
| Setting | Description |
|---|---|
| 1 - 16 | 1-16 ampere. Default is 16 (16 ampere) |
Parameter 10: Meter report interval
Time interval between consecutive meter reports. Meter reports can also be sent as a result of polling. Size: 2 Byte, Default Value: 900
| Setting | Description |
|---|---|
| 30 - 32767 | 30 seconds32767 seconds. |
Parameter 11: Meter report delta value
Meter report delta value Size: 2 Byte, Default Value: 75
| Setting | Description |
|---|---|
| 5 - 3600 | 5-3600W. |
Parameter 2: Power shutdown actions
Decide how the device should react when the overload/overheating features has turned relay OFF Size: 2 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 0 | Disabled and will not retry. User needs to manually turn on afterwards. If temperature overload is on, device will not turn on until device has cooled down. |
| 1 - 32767 | After power shut down (param 1) device will try to turn back ON after delay specified here. (Time in minutes) |
Parameter 3: Switch Type
Decides what type of switch is connected. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Momentary Switch |
| 1 | Toggle Switch |
Parameter 4: S1/Button operation
S1/Button operation Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Button turns load on/off and sends Meter report + Relay status. |
| 1 | Button sends Meter report + Relay status, load can be only controlled wirelessly |
Parameter 5: Scene notifications
Decides if/what scene controller notifications the device sends to gateway. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Sends scene controller for S2. S1 disabled |
| 1 | Sends scene controller for S1. S2 disabled |
| 2 | Sends scene controller for S1 and S2 |
| 3 | Scene controller deactivated. |
Parameter 6: Restore Power Level
Relay power level after power is restored from power-outage.When device is from factory/factory reset the first state of the device should be OFF Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | Always OFF on restored power |
| 1 | Always ON on restored power |
| 2 | Restore last state on restored power (Default) |
Parameter 7: Automatic Turn off
Time to turn relay OFF after having been turned ON Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Auto OFF disabled. |
| 1 - 86400 | Auto OFF timeout in seconds |
Parameter 8: Automatic Turn on
Time to turn relay ON after having been turned OFF Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Auto ON disabled. |
| 1 - 86400 | Auto ON timeout in seconds |
Parameter 9: Inverted Output
Decides if the relay output should be inverted Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Standard operation |
| 1 | Inverted Output |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Binary Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 7.13.7 |
| Certification ID | ZC12-21010159 |
| Z-Wave Product Id | 0x019B.0x0004.0x3500 |
| Electric Load Type | ELV (Electronic)FluorescentIncandescentLEDMLV (Magnetic) |
| Switch Type | Push Button |
| Neutral Wire Required | ok |
| Firmware Updatable | Updatable by Consumer by RF |
| Z-Wave Scene Type | Central Scene |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |