This is a
Heighten your senses with the Jasco Z-Wave Plus Flood/Freeze Sensor. When paired with a compatible hub, the smart sensor provides notification when water levels or temperatures change. Z-Wave devices can also be activated wirelessly for increased convenience and peace of mind. Your automation possibilities are seemingly infinite when connected to a compatible hub. Trigger eventsThe sensor communicates with your hub to initiate desired actions of Z-Wave devices. Increase peace of mind by automatically turning on lights, sending a notification to your phone, activating an alarm or more when temperatures or water levels change. Detection alarmBuilt-in speaker emits audible alert when water levels or temperatures change to allow immediate action by anyone in the area. Dual functionBase contacts and a detachable probe accommodate various setups. Recessed contacts on the base of the sensor are ideal for placement on flat surfaces. The included probe extends reach for use in wells, sump pump holes and other small spaces. Temperature sensorIn temperature-sensitive spaces, protect against costly damage caused by freezing or overheating. Indicator lightLED indicator displays status and provides feedback during programming. It also serves as notification if tampering with the sensor occurs. Universal compatibilityZ-Wave Plus and all previous Z-Wave generations work together to allow continued expansion of your home-automation network.
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Association Group 1 supports Lifeline, Notification, and Device Reset Locally. |
Alternative way to perform Exclusion Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Press button once when prompted to remove device |
1 | Press the button three times quickly when prompted to remove device |
Detection Mode(1:Wet 2:Dry) Size: 2 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Normal Detection (water detected) |
2 | Reverse Detection (Dry Detected) |
Set Temp Report Freq. Size: 2 Byte, Default Value: 60
Setting | Description |
---|---|
5 - 59 | 5... 59 minutes |
60 | Hourly |
360 | 6 hours |
720 | 12 hours |
1440 | Daily |
Set Battery Report Freq. Size: 2 Byte, Default Value: 1440
Setting | Description |
---|---|
5 - 60 | 5... 60 minutes |
360 | Hourly |
720 | 12 hours |
1440 | Daily |
Set Low Temp Level Size: 2 Byte, Default Value: 33
Setting | Description |
---|---|
-4 - 122 | Low Temp |
Set High Temp Level Size: 2 Byte, Default Value: 104
Setting | Description |
---|---|
-4 - 122 | High temp |
Set Temp Report Freq. Size: 2 Byte, Default Value: 60
Setting | Description |
---|---|
5 - 360 | 5... 360 Minutes - Sent every 5 minutes, up to 6 hours |
60 | Hourly |
Set Tamper Indication0 = no LED, no beep (Default)1 = Red LED Flash 5x, no beep2 = Red LED cont flash, no beep3 = no LED, cont beep4 = Red LED cont flash, cont beep Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | No LED, No Beep |
1 | Red LED Flash 5x, no beep |
2 | Red LED continuous flash, no beep |
3 | No LED, continuous beep |
4 | Red LED continuous flash, continuous beep |
Hardware Platform | ZGM130 |
Device Type | Notification Sensor |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 7.06 |
Z-Wave Version | 7.13.5 |
Certification ID | ZC12-20120146 |
Z-Wave Product Id | 0x0063.0x4953.0x3430 |
Firmware Updatable | |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |