Inovelli

Light Strip

SKU: LZW45

ZWave+ Security V2

Quickstart

This is a secure Color Switch DT for XXXQFrequencyName. To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The first addressable RGBTW (Multi-Color + Tunable White) Z-Wave LED Strip & Controller kit from Inovelli which has 45+ built in animations, the ability to build your own animations and heads up notifications (ie: garage door is left open, LED strip can flash red).
Reset to factory default XXXResetDescription
Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Members of this group will receive unsolicited messages related to the status of the controller.
2 5 Sends On & Off commands to associated devices. (1. Single press UP button sends BasicSet (0xFF) and 2. Single press Down sends BasicSet (0x00)
3 5 Sends set level commands to associated devices when the up/down button is pressed.(1. Hold & Release Up or Down button sends SwitchMultiLevelSet which keeps associated devices in sync with this device. 2. Single press Up button sends SwitchMultiLevelSet(0xFF) and 4. Single press Down button sends SwitchMultiLevelSet(0x00)
4 5 Sends start / stop level change to associated devices.(1. Hold Up button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Up)2: Hold Down button sends SW_MULTILEVEL_START_LEVEL_CHANGE (Down) 3. Release Either button sends SW_MULTILEVEL_STOP_LEVEL_CHANGE

Configuration Parameters

Parameter 1: Number of Pixels

When individually addressable LEDs are used, this parameter tells the controller the number of pixels that are attached. 0 - Automatic recognition of pixels. 1..130 - Manually set the number of pixels.
Size: 1 Byte, Default Value: 0

Setting Description
0 Automatic Recognition of Pixels
1 - 130 Manual input of Pixels (1 = 1 Pixel, 2 = 2 Pixels, etc)

Parameter 10: State Power Restored

The state the switch should return to once power is restored after power failure. 0 - Off. 1 - Default Color / Level (Parameter 9). 2 - Previous
Size: 1 Byte, Default Value: 2

Setting Description
0 Off
1 Returns to the default color / level as set in Parameter 9
2 Returns to the previous setting before loss of power

Parameter 17: Active power reports

The power level change that will result in a new power report being sent. The value is a percentage of the previous report. 0 = disabled.
Size: 1 Byte, Default Value: 10

Setting Description
0 Disabled
1 - 100 Set the percentage level change of the previous report (1 = 1%, 2 = 2%, etc)

Parameter 18: Periodic reports

Time period between consecutive power & energy reports being sent (in seconds). The timer is reset after each report is sent.
Size: 2 Byte, Default Value: 3600

Setting Description
0 Disabled
1 - 32767 Set the time period in seconds (1 = 1 second, 2 = 2 seconds, etc)

Parameter 19: Active energy reports

Energy reports Energy level change which will result in sending a new energy report. Available settings: 0 - energy reports disabled, 1-127 (0.01-1.27 kWh) - report triggering threshold, Default setting: 10 (0.1 kWh)
Size: 1 Byte, Default Value: 10

Setting Description
0 Disabled
1 - 127 Report triggering threshold (10 = 0.1 kWh)

Parameter 2: Dimming Speed

This changes the speed in which the lightstrip dims up or down. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. 0 - Instant, 1 - Fast .. 98 - Slow
Size: 1 Byte, Default Value: 3

Setting Description
0 Instant on
1 - 98 Speed of dimming up or down (1 = fast, 98 = slow)

Parameter 21: Quick Strip Effect

Turn on a quick effect that is similar to the LED notifications on our dimmers and switches. See website for details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0

Setting Description
0 - 2147483647 See website for further instructions: https://inovelli.com/lzw45/parameters

Parameter 22: Custom Effect Parameter 1

A custom effect with up to 4 actions can be turned on with correct input for parameters 22-24, 30. This parameter controls the color and transition of those actions. See website for details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0

Setting Description
0 - 2139062143 See website for further instructions: https://inovelli.com/lzw45/parameters

Parameter 23: Custom Effect Parameter 2

A custom effect with up to 4 actions can be turned on with correct input for parameters 22-24, 30. This parameter controls the level of those actions. See website for details.https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0

Setting Description
0 - 1667457891 See website for further instructions: https://inovelli.com/lzw45/parameters

Parameter 24: Custom Effect Parameter 3

A custom effect with up to 4 actions can be turned on with correct input for parameters 22-24, 30. This parameter controls the duration of those actions. See website for details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0

Setting Description
0 - 1010580540 See website for further instructions: https://inovelli.com/lzw45/parameters

Parameter 3: Ramp Rate

This changes the speed in which the lightstrip turns on or off. For example, when a user sends the switch a basicSet(value: 0xFF) or basicSet(value: 0x00), this is the speed in which those actions take place. A setting of 0 should turn the light immediately on or off (almost like an on/off switch). Increasing the value should slow down the transition speed. A setting of 99 should keep this in sync with parameter 2. 0 - Instant. 1 - Fast .. 98 - Slow. 99 - Keep in sync with parameter 2
Size: 1 Byte, Default Value: 99

Setting Description
0 Instant on
1 - 99 Speed of turning on/off (1 = fast, 99 = slow)

Parameter 30: Custom Effect Parameter 4

A custom effect with up to 4 actions can be turned on with correct input for parameters 22-24, 30. This parameter controls the number of iterations, the end effect, and the scale of the duration in parameter 24. See website for details. https://inovelli.com/lzw45/parameters
Size: 4 Byte, Default Value: 0

Setting Description
0 - 197375 See website for further instructions: https://inovelli.com/lzw45/parameters

Parameter 31: Pixel Effect

Turn on an effect that utilizes the individually addressable LEDs. Byte 0 = Effect, Byte 1 = Level
Size: 2 Byte, Default Value: 0

Setting Description
0 - 32767 See website for further instructions: https://inovelli.com/lzw45/parameters

Parameter 4: Minimum Level

The minimum level that the strip can be dimmed to. Useful when the user has an LED strip that does not turn on or flickers at a lower level.
Size: 1 Byte, Default Value: 1

Setting Description
1 - 45 Percent value of the minimum dim level (1 = 1%, 2 = 2%, etc)

Parameter 5: Maximum Level

The maximum level that the strip can be dimmed to. Useful when the user has an LED strip that reaches its maximum level before the dimmer value of 99.
Size: 1 Byte, Default Value: 99

Setting Description
55 - 99 Percent value of the maximum dim level (55 = 55%, 56 = 56%, etc)

Parameter 51: Button Delay

The 700ms delay that occurs after pressing the physical button to turn the switch on/off is removed. Consequently this also removes the following scenes: 2x, 3x, 4x, 5x tap. Still working are the 1x tap, held, released, and the level up/down scenes.
Size: 1 Byte, Default Value: 1

Setting Description
0 Yes - Disable 700ms delay
1 No - Do not disable 700ms delay

Parameter 6: Auto Off Timer

Automatically turns the strip off after this many seconds. When the strip is turned on a timer is started that is the duration of this setting. When the timer expires, the strip is turned off. 0 - Auto off is disabled
Size: 2 Byte, Default Value: 0

Setting Description
0 Auto-off is disabled
1 - 32767 Amount of seconds until the lightstrip turns off automatically (1 = 1 second, 2 = 2 seconds, etc)

Parameter 7: Default Level(Local)

Default level for the strip when it is powered on from the local switch. A setting of 0 means that the switch will return to the level that it was on before it was turned off. 0 - Previous
Size: 1 Byte, Default Value: 0

Setting Description
0 Returns lightstrip to the previous level prior to being turned off
1 - 99 Percent level to turn the lightstrip to when turned on (1 = 1%, 2 = 2%, etc)

Parameter 8: Default Level (Z-Wave)

Default level for the dimmer when it is powered on from a Z-Wave command (i.e. BasicSet(0xFF). A setting of 0 means that the switch will return to the level that it was on before it was turned off. 0 - Previous
Size: 1 Byte, Default Value: 0

Setting Description
0 Returns lightstrip to the previous level prior to being turned off
1 - 99 Percent level to turn the lightstrip to when turned on (1 = 1%, 2 = 2%, etc)

Parameter 9: Default Color&Temp

Byte(3-2): Values between 2700-6500 represent a color temperature. Byte(1-0): Values between 1-360 represent the color on the Hue color wheel. The value of 361 represents a random color and a value of 0 represents the previous color.
Size: 4 Byte, Default Value: 0

Setting Description
0 Returns the lightstrip to the previous color when turned on
1 - 360 Represents the values of the hue color wheel
2700 - 6500 Represents the values of color temperature (Kelvins) where 2700 is warm white and 6500 is cool white

Technical Data

Hardware Platform ZGM130
Device Type Color Switch DT
Network Operation Always On Slave
Firmware Version HW: 1 FW: 1.20
Z-Wave Version 7.13.4
Certification ID ZC12-20110133
Z-Wave Product Id 0x031E.0x000A.0x0001
Color White
IP (Ingress Protection) Rated ok
Firmware Updatable Updatable by Consumer by RF
Outdoor Use ok
Z-Wave Scene Type Central Scene
Communications Protocol Z-Wave Z/IP
Frequency XXfrequency
Maximum transmission power XXantenna
Color Switch DT