iBlinds
iblinds v3Window Blind Motor
SKU: IB3.0
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
iblinds is a simple Z-Wave Plus device used to automate your existing window blinds. You can control any 2-2inch corded lift horizontal blinds in your home or office. Set a scheduled to open at sunrise and close at sunset, use voice control with Amazon Alexa and Google Home or manually control a single blind, or a group of them, from home or anywhere in the world with one touch of a button using your smartphone, tablet or Z-Wave remote.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Battery and Switch Multilevel lifeline reports |
Configuration Parameters
Parameter 1: Close Interval
Used for auto calibration. Sets interval endpoint detection. Smaller interval will make the blinds close tighter. Size: 1 Byte, Default Value: 22
| Setting | Description |
|---|---|
| 15 - 30 | Smaller interval will make the blinds close tighter |
Parameter 2: Reverse Direction
Used to reverse the direction of the blinds. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Forward Direction - 0% = Closed Down |
| 1 | Reverse Direction - 0% = Closed Up |
Parameter 3: Disable Report
Used to disable Z-Wave Report. This is useful for systems that poll iblinds immediately after sending a position command. Disable if this an immediate report is causing iblinds motor to function improperly. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Enable Device Reset Locally |
| 1 | Disable Device Reset Locally |
Parameter 4: Default ON Value
Used to set the default ON Level when manual push button is pushed- Default value for ON = 50% (0x32) , change this value if you wish to set the push button ON value to a different preset value. Size: 1 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 99 | Set the default On Value |
Parameter 5: Reserved
Reserved for Manufactuer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | Reserved for Manufactuer |
Parameter 6: Speed
Used to set the default blind Speed. 0= No Delay. The Larger the number the slower the speed. Note: Duration Value >0 will always override the speed parameter Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 100 | The larger the value the slower the speed |
Technical Data
| Hardware Platform | ZGM130 |
| Device Type | Window Covering DT |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 1 FW: 3.01 |
| Z-Wave Version | 7.12.2 |
| Certification ID | ZC12-20110129 |
| Z-Wave Product Id | 0x0287.0x0004.0x0071 |
| Window Covering Control Features | Automatic CalibrationEndpoint AwarePosition AwareSupports Horizontal Blinds/LouversSupports Tilt Motion |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |