This is a
This device measures the three air quality parameters temperature, humidity and dew point and reports them to a central controller. Besides this, the device can directly control groups of other Z-Wave devices on over- and undershooting a set temperature and/or humidity parameter. This can be used to establish control loops for temperature and humidity. The device wakes up every 15 minutes to measure the values and it will send unsolicited reports when values change. Additionally, the device will report all values on request.
The mold detector is actively monitoring the danger of mold in a room based on the temperature and humidity and will issue alarm warnings when critical air conditions met. Wireless Alarm and red and a green blinking LED will indicate a mold condition. This local LED warning function is also available when the device is not included in any Z-Wave network and works stand alone.
Just place the device on any flat surface. Please keep in mind that the temperature may be different in different locations inside the room. If placed too close to the heating both temperature, humidity and dew point values may be wrong. The device is IP 20 rated. This means that is must not be exposed to direct water (rain). It is safe to use the device in a humid environment such as a bathroom or dedicated washing facility.
Once the device is powered up it will start monitoring the air parameters and warn of mold using the local red and green LED. All air parameters are measured every 15 minutes. Pushing the button will force an immediate measurement and the LEDs will indicate the danger of mold
Reset to factory default | Keep the button pressed for 10 seconds. After 5 seconds the red LED will start blinking. |
Inclusion | 1. Insert the battery. 2. Press the button quickly three times in a row. |
Exclusion | 1. Press the button quickly three times in a row. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | Wake Up the device by pressing the central button once. |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Lifeline |
2 | 5 | Temperature High Trigger |
3 | 5 | Temperature Low Trigger |
4 | 5 | Humidity High Trigger |
5 | 5 | Humidity Low Trigger |
6 | 5 | Air Temperature |
This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active. Size: 1 Byte, Default Value: 20
Setting | Description |
---|---|
0 | disabled |
1 - 100 | 1/10 degree |
This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | disabled |
1 - 20 | % |
This parameter defines the time interval to send an unsolicited report. If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active. Size: 2 Byte, Default Value: 43200
Setting | Description |
---|---|
0 | disabled |
900 - 65535 | Seconds |
This parameter defines a temperature. If the measured temperature surpasses this watermark a BASIC command is sent into Association Group 2 Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | disabled |
1 - 1000 | 1/10 degree |
This parameter defines a temperature. If the measured temperature dropps below this watermark a BASIC command is sent into Association Group 3 Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 | disabled |
200 - 1000 | 1/10 degree |
This parameter defines a relative humidity. If the measured relative humidity surpasses this watermark a BASIC command is sent into Association Group 4 Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | disabled |
1 - 90 | % |
This parameter defines a relative humidity. If the measured temperature dropps below this relative humidity a BASIC command is sent into Association Group 5 Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | disabled |
1 - 90 | % |
This defines what BASIC command shall be sent out into association group 3 Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 - 255 | Value |
This defines what BASIC command shall be sent out into association group 2 Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 255 | Value |
This defines what BASIC command shall be sent out into association group 5 Size: 1 Byte, Default Value: 255
Setting | Description |
---|---|
0 - 255 | Value |
This defines what BASIC command shall be sent out into association group 4 Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 255 | Value |
This value allows to increase the humidity threshold for mold danger notification by max 10% Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 10 | % |
This parameter sets the temperature scale. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | Celsius |
2 | Fahrenheit |
This parameter helps reset configuration parameters and the device to factory defaults Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1 - 1431655764 | Reset all Parameter settings to their default settings. |
1431655765 | Completely factory reset sensor and send device reset locally notification. |
Dimensions | 34x34x16 mm |
Hardware Platform | ZGM130S |
EAN | 1220000016644 |
IP Class | IP 20 |
Battery Type | 1 * CR2477 |
Device Type | Notification Sensor |
Generic Device Class | GENERIC TYPE SENSOR NOTIFICATION (0x07) |
Specific Device Class | SPECIFIC TYPE NOTIFICATION SENSOR (0x01) |
Network Operation | Reporting Sleeping Slave |
Firmware Version | 01.00 |
Z-Wave Version | 07.12 |
Certification ID | ZC12-20080086 |
Z-Wave Product Id | 0371.0002.0009 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |