Aeotec

Door / Window Sensor 7 Pro

SKU: ZWA012-A

ZWave+ Security V2

Quickstart

This is a secure Notification Sensor for XXXQFrequencyName. To run this device please make sure the internal battery is fully charged.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Aeotec Door/ Window Sensor 7 Pro is built on the 700 series Z-Wave technology. Its a small window position sensor for your smart home, it monitors window and their exact opening position and lets your know when a window is tilted or completely opened. It also supports connecting external binary sensors with a dry contact through the dry binary contact of the Door/ Window sensor. Using the latest technology it supports the highest Z-Wave security level of S2 and SmartStart.

Reset to factory default XXXResetDescription
Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline to Gateway
2 5 Control devices when a magnet or external dry contacts trips
3 5 Sends out alarm message when a magnet or external dry sensor trips
4 5 Sends alarm messages when tamper is tripped
5 5 Control devices when tilting sensor trips

Configuration Parameters

Parameter 1: Sensor Operation Mode

This parameter defines if the internal magnet sensor or the external terminal input is detected and used to issue alarm notification. There is always one input active only. The other sensor input the deactivated.
Size: 1 Byte, Default Value: 0

Setting Description
0 Internal Magnet Sensor Used and scene activation enabled
1 - 0 External Terminal Inputs Used and scene activation disabled

Parameter 10: Time Delay of u0022Onu0022 command frame

On command is sent after a delay defined in this parameter.
Size: 2 Byte, Default Value: 0

Setting Description
0 - 32400 seconds

Parameter 11: Time Delay of u0022Offu0022 command frame

Off command is sent after a delay defined in this parameter.
Size: 2 Byte, Default Value: 0

Setting Description
0 - 32400 seconds

Parameter 12: Delay of Tamper Alarm Cancellation

Time a tamper alarm is delayed.
Size: 2 Byte, Default Value: 0

Setting Description
0 - 32400 seconds

Parameter 13: Reporting Tamper Alarm Cancellation

This parameter defines if the alarm cancellation event is reported.
Size: 1 Byte, Default Value: 1

Setting Description
0 Do not send Report
1 - 0 Send Report

Parameter 14: Central Scene Event Functionality

This parameter enables/disablesthe central scene function.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disabled
1 - 0 Enabled

Parameter 15: Tilt Sensor Functionality

This parameter enables/disablesthe tilt function.
Size: 1 Byte, Default Value: 1

Setting Description
0 Disabled
1 - 0 Enabled

Parameter 16: Tilt Sensor State

This parameter allows to set in what state is door/window when the tilt is in an OFF state.
Size: 1 Byte, Default Value: 0

Setting Description
0 OFF when sensor is vertical
1 - 0 ON when sensor is vertical

Parameter 17: 5th Association Group triggers

Parameter defines events which result in sending On/Off commands to devices added to the 2nd Association Group. These commands are sent alternately to switch the devices On and Off. Commands represent the values of BASIC SET command frames.
Size: 1 Byte, Default Value: 0

Setting Description
0 Switch after Open and Close
1 Switch after Open
2 Switch after Close

Parameter 18: Commands sent to 5th Association Group

Command frames sent to devices added to the 5th association group.
Size: 1 Byte, Default Value: 2

Setting Description
0 On
1 Off
2 On and Off

Parameter 19: Value of ON command frame sent to 5th Associatio

The value of 0 turns OFF the device, 255 turns it On. In case of associating the Dimmer or Roller Shutter module, values 1-99 allow to set an Associated device to a specified level.0-99 or 255
Size: 1 Byte, Default Value: 255

Setting Description
0 - 99 Value
255 Value

Parameter 2: Dry Contact Operation Mode

Parameter defines how dry contact will operate with the sensor or switch that is connected to the dry contact terminals.0 - NO Toggle / Follow state will follow the input of the dry contact terminals where OFF is CLOSED, and ON is OPEN.1 - NC Toggle / Follow state will follow the input of the dry contact terminals where ON is CLOSED, and OFF is OPEN.2 - NO save state will allow state of sensor to toggle OPEN/CLOSE based on OFF to ON signal.3 - NC save state will allow state of sensor to toggle OPEN/CLOSE based on ON toOFF signal.
Size: 1 Byte, Default Value: 0

Setting Description
0 NO Toggle / Follow state will follow the input of the dry contact terminals where OFF is CLOSED, and ON is OPEN.
1 NC Toggle / Follow state will follow the input of the dry contact terminals where ON is CLOSED, and OFF is OPEN.
2 NO save state will allow state of sensor to toggle OPEN/CLOSE based on OFF to ON signal.
3 NC save state will allow state of sensor to toggle OPEN/CLOSE based on ON toOFF signal.

Parameter 21: Tilt sensitivity

You can use this parameter to adjust the tilt sensitivity if the tilt is too low or too high.
Size: 1 Byte, Default Value: 50

Setting Description
1 - 100 Tilt Sensitivity

Parameter 255: Reset Parameter

0Nothing happens0x55555555Completely factory reset sensor and send device reset locally notification.All other valuesReset all Parameter settings to their default settings.
Size: 4 Byte, Default Value: 0

Setting Description
1 - 1431655764 Reset all Parameter settings to their default settings.
1431655765 Completely factory reset sensor and send device reset locally notification.

Parameter 3: Sensor State Polarity

This parameter defines the polarity of the magnet sensor.
Size: 1 Byte, Default Value: 0

Setting Description
0 Closed when Magnet near
1 - 0 Opened when Magnet near

Parameter 4: Visual LED Indications

This parameter defines when the red LED will indicate events. Disabling all indications may extend battery life.
Size: 1 Byte, Default Value: 7

Setting Description
0 LED indication Off
1 - 0 Open/Close Status Change
2 - 0 Wake Up
3 - 0 Open/Close Status Change + Wake Up (1+2 summarized)
4 - 0 Device Tampering
5 - 0 Open/Close Status Change + Device Tampering (1 + 5 summarized)
6 - 0 Wake Up + Device Tampering (2 + 4 summarized)
7 - 0 All LED indications on (values 1 + 2 + 4 summarized)

Parameter 5: Range Test after double click

Allows to enable the activation of a Z-Wave range test with double clicking the tamper switch.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disabled
1 - 0 Enabled

Parameter 6: 2nd Association Group Trigger

This parameter defines the status of the magnet switch that causes sending a BASIC command to all devices of Association Group 2.
Size: 1 Byte, Default Value: 0

Setting Description
0 Switch after Open and Close
1 - 0 Switch after Open
2 - 0 Switch after Close

Parameter 7: Command Sent to Devices of Association Group 2

This parameter defines which commands is sent to 2nd Association Group
Size: 1 Byte, Default Value: 2

Setting Description
0 On
1 - 0 Off
2 - 0 On and Off

Parameter 8: BASIC command u0022On eventu0022 value

This is the BASIC command value sent in case of u0022Onu0022 event.
Size: 1 Byte, Default Value: 255

Setting Description
0 - 99 Value
255 Value

Parameter 9: BASIC command u0022Off eventu0022 value

This is the BASIC command value sent in case of u0022Offu0022 event.
Size: 1 Byte, Default Value: 0

Setting Description
0 - 99 Value
255 Value

Technical Data

Hardware Platform ZGM130
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Firmware Version HW: 1 FW: 1.00
Z-Wave Version 7.12.2
Certification ID ZC12-20080085
Z-Wave Product Id 0x0371.0x0102.0x000C
Color White
Z-Wave Scene Type Central Scene
Frequency XXfrequency
Maximum transmission power XXantenna
Notification Sensor