Heatit controls
HeatitZ-Temp2
SKU: Z-Temp2
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Heatit Z-Temp2 is a battery-operated thermostat designed for usewith water based heating systems. Used in combination with theHeatit Z-Water regulator you can control your heating system with aZ-Wave primary controller/gateway with the use of Heatit Z-Water incombination with one or several Heatit Z-Temp2.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifeline. Normally used by the Z-WaveController. |
| 2 | 5 | Multilevel Sensor Report (internal measured temperate and measured relative humidity). |
| 3 | 5 | Binary Switch Set (normally used to control external relays). |
Configuration Parameters
Parameter 1: Temperature/ Humidity report interval
Used to adjust the time between report interval for Temperature and humidity reports. Size: 2 Byte, Default Value: 900
| Setting | Description |
|---|---|
| 30 - 32767 | 30 to 32 767 seconds (Default 900) |
Parameter 10: Temperature Control Hysteresis
Adjust the delta values for the thermostat to turn on off heating. Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 3 - 30 | 0.3 to 3C (Default 5, 0,5C) |
Parameter 11: Minimum Temperature Limit
Set the minimum temperature limit. Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 50 - 400 | 5 to 40C (Default 50, 5C) |
Parameter 12: Maximum Temperature Limit
Set the maximum temperature limit. Size: 2 Byte, Default Value: 400
| Setting | Description |
|---|---|
| 50 - 400 | 5 to 40C (Default 400, 40C) |
Parameter 13: External Relay & Operating State update interva
Set time on how often the devices sends Binary Switch Set and thermostat mode to gateway. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Sends only when changed (Default) |
| 1 - 240 | 1 to 240 minutes + When changed |
Parameter 14: Report when presence is detected
Decides if the thermostat sends temperature when presence is detected. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Do not report to gateway when presence is detected, only at interval. (Default) |
| 1 | Send temperature report to gateway when presence is detected. |
Parameter 2: Temperature delta value
Temperature delta value. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | Reporting temperate based on change is disabled |
| 5 - 50 | 0.5 to 5C (Default 10, 1.0C) |
Parameter 3: Humidity delta value
Humidity delta value. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | Reporting temperate based on change is disabled |
| 5 - 50 | 5 to 50% (Default 10, 10%) |
Parameter 4: Temperature offset settings
Calibrate the internal sensor. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -100 - 100 | -100 to 100C (Default 0, 0C) |
Parameter 5: Humidity offset settings
Offsets the measured relative humidity. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -100 - 100 | -10 to 10% (Default 0, 0%) |
Parameter 6: Proximity sensor retrigger interval
Proximity sensor retrigger interval. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 2 - 270 | 2 to 270 seconds (Default 10, 10 seconds) |
Parameter 7: Proximity sensorEnable / Disable
Choose if proximity sensor is used or not. Size: 2 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable (Default) |
Parameter 8: LED maximum brightness
Adjust the backlight of LCD display. Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 99 | 0 to 99% (Default 50, 50%) |
Parameter 9: LED turned on before timeout
Adjust the time from proximity sensor / display touched until display goes to sleep. Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 3 - 300 | 3 to 300 secounds (Default 3, 3 seconds). |
Technical Data
| Hardware Platform | EFR32Z |
| Device Type | Thermostat - HVAC |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.01:00.02 |
| Z-Wave Version | 7.11.1 |
| Certification ID | ZC12-20050065 |
| Z-Wave Product Id | 0x019B.0x0004.0x0204 |
| Thermostat HVAC Systems Supported | Dual FuelHumidity ControlUniversal |
| Thermostat Modes | Heat |
| Color | White |
| Thermostat Power Source | Battery |
| Firmware Updatable | Updatable by Manufacturer |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |