Minoston
Z-Wave Plug with Energy Monitor
SKU: MP31ZP
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The MP31ZP is a mini plug-in outlet equipped with Z-Wavecapabilities and energy monitoring for additional convenience. This smart plug allows you to plug in and access an appliance through the certified Z-Wave hubs.Schedule your appliances, run a timer, or check the On/Off status to monitor and save energy.The compact size gives full access to the second outlet in a standard receptacle.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Lifeline |
| 2 | 5 | Basic Set Command |
| 3 | 5 | basic set command |
Configuration Parameters
Parameter 1: Restores state after power failure
Restores state after power failure Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The state before a power outage. |
| 1 | outlet on |
| 2 | outlet off |
Parameter 10: Endpoint1 Enable Auto Turn-ON Timer
Endpoint1 Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Auto Turn-ON Timer Disabled |
| 1 | Auto Turn-ON Timer Enabled |
Parameter 11: Endpoint1 Count Down Configuration(Turn on the output by time
Endpoint1 Count Down Configuration(Turn on the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint1 Count Down Configuration(Turn on the output by time |
Parameter 12: Endpoint2 Enable Auto Turn-OFF Timer
Endpoint2 Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Auto Turn-OFF Timer Disabled |
| 1 | Auto Turn-OFF Timer Enabled |
Parameter 13: Endpoint2 Count Down Configuration(Turn off the output by time
Endpoint2 Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint2 Count Down Configuration(Turn off the output by time |
Parameter 14: Parameter Endpoint2 Enable Auto Turn-ON Timer
Endpoint2 Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Auto Turn-ON Timer Disabled |
| 1 | Auto Turn-ON Timer Enabled |
Parameter 15: Endpoint2 Count Down Configuration(Turn on the output by time
Endpoint2 Count Down Configuration(Turn on the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint2 Count Down Configuration(Turn on the output by time |
Parameter 16: Manual Control
Manual Control Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Manual Control Disabled |
| 1 | manual control enabled |
Parameter 17: Status LED Configuration
Status LED Configuration Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | LED indicator will display power consumption whenever the device is plugged in |
| 1 | LED indicator will display power consumption whenever the device is ON in and will turn off when the plug is OFF |
| 2 | LED indicator will display the level of power consumption for 5 seconds only whenever the device is turned on or off |
| 3 | Always OFF |
Parameter 2: Power Wattage Report Value Threshold(Wattage)
Power Wattage Report Value Threshold(Wattage) Size: 4 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 65535 | Power Wattage Report Value Threshold(Wattage) |
Parameter 3: Power Wattage Report Frequency (Timer)
Power Wattage Report Frequency (Timer) Size: 4 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 0 - 2678400 | Power Wattage Report Frequency (Timer) |
Parameter 4: Energy (kWh) Report Frequency (Timer)
Energy (kWh) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Energy (kWh) Report Frequency (Timer) |
Parameter 5: Parameter Voltage (V) Report Frequency (Timer)
Voltage (V) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Voltage (V) Report Frequency (Timer) |
Parameter 6: Electricity (A) Report Frequency (Timer)
Electricity (A) Report Frequency (Timer) Size: 4 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 30 - 2678400 | Electricity (A) Report Frequency (Timer) |
Parameter 7: Overload Protection (Current)
Overload Protection (Current) Size: 1 Byte, Default Value: 13
| Setting | Description |
|---|---|
| 1 - 16 | Overload Protection (Current) |
Parameter 8: Endpoint1 Enable Auto Turn-OFF Timer
Endpoint1 Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Auto Turn-OFF Timer Disabled |
| 1 | Auto Turn-OFF Timer Enabled |
Parameter 9: Endpoint1 Count Down Configuration(Turn off the output by time
Endpoint1 Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 65535 | Endpoint1 Count Down Configuration(Turn off the output by time |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 1.00 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-22057087 |
| Z-Wave Product Id | 0x0312.0xFF00.0xFF0E |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |