Nice
On/Off-Control
SKU: FGS-223
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
On/Off-Control is designed to be installed in standard wall switch boxes or anywhere else where it is necessary to control electric devices.On/Off-Control allows to control connected devices either via the Z-Wave Plus network or via a switch connected directly to it and is equipped with active power and energy consumption metering functionality
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | u0022Lifelineu0022 reports the device status and allows for assigning single device only (main controller by default). |
| 2 | 5 | On/Off (S1) is assigned to S1 input terminal (uses Basic command class). |
| 3 | 5 | u0022Dimmer (S1)u0022 is assigned to S1 input terminal (uses Switch Multilevel command class). |
| 4 | 5 | On/Off (S2) is assigned to S2 input terminal (uses Basic command class). |
| 5 | 5 | u0022Dimmer (S2)u0022 is assigned to S2 input terminal (uses Switch Multilevel command class). |
Configuration Parameters
Parameter 1: Restore state after power failure
This parameter determines if the device will return to state prior to the power failure after power is restored. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | Restore state after power failure |
Parameter 10: Switch type
This parameter defines as what type the device should treat the switch connected to the S1 and S2 terminals. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | Switch type |
Parameter 11: Flashing mode - reports
This parameter allows to define if the device sends reports during the flashing mode Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | Flashing mode - reports |
Parameter 12: Associations in Z-Wave network security mode
This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. This parameter does not apply to 1st Lifeline group.Parameter 27 values may be combined, e.g. 1+2=3 means that 2nd and 3rd groups are sent as secure. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 15 | Associations in Z-Wave network security mode |
Parameter 13: S1 switch - scenes sent
This parameter determines which actions result in sending scene IDs assigned to them.Parameter 28 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 15 | S1 switch - scenes sent |
Parameter 14: S2 switch - scenes sent
This parameter determines which actions result in sending scene IDs assigned to them.Parameter 29 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 15 | S2 switch - scenes sent |
Parameter 15: S1 switch - associations sent to 2nd and 3rd association groups
This parameter determines which actions are ignored when sending commands to devices associated in 2nd and 3rd association group. All actions are active by default.Parameter 30 values may be combined, e.g. 1+2=3 means that associations for turning ON and OFF are not sent.*Hold and release is inactive when parameter 20 is set to 1 or 2.**Double click is inactive when parameter 20 is set to 1. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 8 | S1 switch - associations sent to 2nd and 3rd association groups |
Parameter 16: S1 switch - Switch ON value sent to 2nd and 3rd association groups
This parameter defines value sent with Switch ON command to devices associated in 2nd and 3rd association group. Size: 2 Byte, Default Value: 255
| Setting | Description |
|---|---|
| 0 - 255 | S1 switch - Switch ON value sent to 2nd and 3rd association groups |
Parameter 17: S1 switch - Switch OFF value sent to 2nd and 3rd association groups
This parameter defines value sent with Switch OFF command to devices associated in 2nd and 3rd association group. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | S1 switch - Switch OFF value sent to 2nd and 3rd association groups |
Parameter 18: S1 switch - Double Click value sent to 2nd and 3rd association groups
This parameter defines value sent with Double Click command to devices associated in 2nd and 3rd association group. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | S1 switch - Double Click value sent to 2nd and 3rd association groups |
Parameter 19: S1 switch - Double Click value sent to 2nd and 3rd association groups
This parameter defines value sent with Double Click command to devices associated in 2nd and 3rd association group. Size: 2 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 0 - 255 | S1 switch - Double Click value sent to 2nd and 3rd association groups |
Parameter 2: First channel - operating mode
This parameter allows to choose operating for the 1st channel controlled by the S1 switch. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 5 | First channel - operating mode |
Parameter 20: S2 switch - associations sent to 4th and 5th association groups
his parameter determines which actions result in sending commands to devices associated in 4th and 5th association group. All actions are active by default. Parameter 35 values may be combined, e.g. 1+2=3 means that associations for turning ON and OFF are not sent.*Hold and release is inactive when parameter 20 is set to 1 or 2.**Double click is inactive when parameter 20 is set to 1 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 8 | S2 switch - associations sent to 4th and 5th association groups |
Parameter 21: S2 switch - Switch ON value sent to 4th and 5th association groups
This parameter defines value sent with Switch ON command to devices associated in 4th and 5th association group. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | S2 switch - Switch ON value sent to 4th and 5th association groups |
Parameter 22: S2 switch - Switch OFF value sent to 4th and 5th association groups
This parameter defines value sent with Switch OFF command to devices associated in 4th and 5th association group. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | S2 switch - Switch OFF value sent to 4th and 5th association groups |
Parameter 23: S2 switch - Double Click value sent to 4th and 5th association groups
This parameter defines value sent with Double Click command to devices associated in 4th and 5th association group. Size: 2 Byte, Default Value: 99
| Setting | Description |
|---|---|
| 0 - 255 | S2 switch - Double Click value sent to 4th and 5th association groups |
Parameter 24: Reaction to General Alarm
This parameter determines how the device will react to General Alarm frame. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 - 3 | Reaction to General Alarm |
Parameter 25: Reaction to Flood Alarm
This parameter determines how the device will react to Flood Alarm frame. Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 - 3 | Reaction to Flood Alarm |
Parameter 26: Reaction to CO/CO2/Smoke Alarm
This parameter determines how the device will react to CO, CO2 or Smoke frame. Size: 1 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 0 - 3 | Reaction to CO/CO2/Smoke Alarm |
Parameter 27: Reaction to Heat Alarm
This parameter determines how the device will react to Heat Alarm frame. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 3 | Reaction to Heat Alarm |
Parameter 28: Flashing alarm duration
This parameter allows to set duration of flashing alarm mode. Size: 2 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 0 - 32000 | Flashing alarm duration |
Parameter 29: First channel - power reports
This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 0 - 100 | First channel - power reports |
Parameter 3: First channel - reaction to switch for delay/auto ON/OFF modes
This parameter determines how the device in timed mode reacts to pushing the switch connected to the S1 terminal. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | reaction to switch for delay/auto ON/OFF modes |
Parameter 30: First channel - minimal time between power reports
This parameter determines minimum time that has to elapse before sending new power report to the main controller Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 120 | First channel - minimal time between power reports |
Parameter 31: First channel - energy reports
This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. Size: 2 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 32000 | First channel - energy reports |
Parameter 32: Second channel - power reports
This parameter determines the minimum change in consumed power that will result in sending new power report to the main controller. Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 0 - 100 | Second channel - power reports |
Parameter 33: Second channel - minimal time between power reports
This parameter determines minimum time that has to elapse before sending new power report to the main controller. Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 120 | Second channel - minimal time between power reports |
Parameter 34: Second channel - energy reports
This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. Size: 2 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 32000 | Second channel - energy reports |
Parameter 35: Periodic power reports
This parameter determines in what time interval the periodic power reports are sent to the main controller Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 0 - 32000 | Periodic power reports |
Parameter 36: Periodic energy reports
This parameter determines in what time interval the periodic energy reports are sent to the main controller. Size: 2 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 0 - 3600 | Periodic energy reports |
Parameter 37: Measuring energy consumed by the device itself
This parameter determines whether energy metering should include the amount of energy consumed by the device itself. Results are being added to energy reports for first endpoint. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | Measuring energy consumed by the device itself |
Parameter 4: First channel - time parameter for delay/auto ON/OFF modes
This parameter allows to set time parameter used in timed modes. Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 32000 | time parameter for delay/auto ON/OFF modes |
Parameter 5: First channel - pulse time for flashing mode
This parameter allows to set time of switching to opposite state in flashing mode Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 32000 | pulse time for flashing mode |
Parameter 6: Second channel - operating mode
This parameter allows to choose operating for the 1st channel controlled by the S2 switch. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 5 | Second channel - operating mode |
Parameter 7: Second channel - reaction to switch for delay/auto ON/OFF modes
This parameter determines how the device in timed mode reacts to pushing the switch connected to the S2 terminal. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 2 | Second channel - reaction to switch for delay/auto ON/OFF modes |
Parameter 8: Second channel - time parameter for delay/auto ON/OFF modes
This parameter allows to set time parameter used in timed modes. Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 32000 | Second channel - time parameter for delay/auto ON/OFF modes |
Parameter 9: Second channel - pulse time for flashing mode
This parameter allows to set time of switching to opposite state in flashing mode. Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 32000 | Second channel - pulse time for flashing mode |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 3 FW: 3.04 |
| Z-Wave Version | 6.51.07 |
| Certification ID | ZC10-22047084 |
| Z-Wave Product Id | 0x010F.0x0203.0x1000 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |