Plug-Control E/F

Parameter 1: Always On mode

In this mode Plug-Control will turn on connected device permanently and will stop reacting to attempts of turning it off (through Z-Wave network or pushing the B-button).Always On function turns Plug-Control into a power and energy meter. Connected device will not be turned off upon receiving an alarm frame from another Z-Wave device (parameter 31 will be ignored).In Always on mode, connected device may be turned off after exceeding the power defined in parameter 3 or in case of detecting current greater than 110% of rated current. In such cases, connected device can be turned on again by pushing the B-button or sending a control frame. By default, overload protection is inactive.
Size: 1 Byte, Default Value: 0

Setting	Description
0	function inactive
1	function activated

Parameter 10: High priority power report

This parameter determines the minimum percentage change in active power that will result in sending power report to the main controller with the highest priority in the Z-Wave network.By default, Plug-Control immediately sends the power report if the power load changes by 80%.
Size: 1 Byte, Default Value: 80

Setting	Description
1 - 99	power change in percent
100	reports are disabled

Parameter 11: Standard power report

This parameter determines the minimum percentage change in active power that will result in sending power report to the main controllerCompared to parameter 10, the maximum number of reports sent is reduced (parameter 12) to 5 in a specified time interval. In addition, the reports are not sent in mode, which may result in overloading the Z-Wave network.By default changes in power load may be reported up to 5 times per 30 seconds, when power load changes by 15%.
Size: 1 Byte, Default Value: 15

Setting	Description
1 - 99	power change in percent
100	reports are disabled

Parameter 12: Power reporting interval

This parameter defines the time interval of sending at most 5 standard power reports when the power changes by the value set in parameter 11. The higher the value of parameter 12, the fewer reports the device will send.By default Plug-Control sends up to 5 reports each 30 seconds, provided the power load changes by 15%.
Size: 2 Byte, Default Value: 30

Setting	Description
5 - 600	in seconds

Parameter 13: Energy reporting threshold

This parameter specifies the minimum change in energy consumption (in relation to the previously reported), that will result in sending a new report.
Size: 2 Byte, Default Value: 10

Setting	Description
0	energy reports inactive
1 - 500	(0.01 - 5 kWh, step 0.01 kWh) - threshold

Parameter 14: Power and energy periodic reports

This parameter defines time period between independent reports sent when changes in power load have not been recorded or if changes are insignificant. By default reports are sent every hour.
Size: 2 Byte, Default Value: 3600

Setting	Description
0	periodic reports inactive
5 - 32400	in seconds

Parameter 15: Measuring energy consumed by the Wall Plug itself

This parameter determines whether power metering should include the amount of power consumed by Plug-Control itself. Results are being added to the value of power consumed by controlled device.
Size: 1 Byte, Default Value: 0

Setting	Description
0	function inactive
1	function activated

Parameter 2: Remember device status before the power failure

This parameter determines how Plug-Control will react in the event of power supply failure (e.g. power outage or taking out from the electrical outlet).After the power supply is back on, Plug-Control can be restored to previous state or remain switched off.This parameter is ignored in Always On mode - the device automatically turns ON after plugging it into the socket.
Size: 1 Byte, Default Value: 0

Setting	Description
0	device remains switched off
1	device restores the state from before the power failure

Parameter 20: Control of On/Off (Button) association group (2) devices

Controlling devices with the B-Button. This parameter is inactive in Always On mode (parameter 1).Control as Plug-Control: switching Plug-Control onswitch the devices on (parameter 24) switching Plug-Control offswitch the devices off (parameter 24)Control opposite to Plug-Control: switching Plug-Control onswitch the devices off switching Plug-Control offswitch the devices on
Size: 1 Byte, Default Value: 0

Setting	Description
0	control as the Wall Plug
1	control opposite to the Wall Plug

Parameter 21: DOWN value - On/Off (Power) association group (3)

Lower power threshold, used in parameter 23. DOWN value cannot be higher than a value specified in parameter 22.
Size: 2 Byte, Default Value: 300

Setting	Description
0 - 24900	0.0 - 2490.0 W, step 0.1 W

Parameter 22: UP value - On/Off (Power) association group (3)

Upper power threshold, used in parameter 23. UP value cannot be lower than a value specified in parameter 21.
Size: 2 Byte, Default Value: 500

Setting	Description
100 - 25000	10.0 - 2500.0 W, step 0.1 W

Parameter 23: The response after exceeding defined power values

This parameter defines the way that 3rd association group devices are controlled. Depends on the actual measured power (as parameters 21 and 22 settings).
Size: 1 Byte, Default Value: 6

Setting	Description
1	turn the associated devices ON, once the power drops below DOWN value (parameter 21)
2	turn the associated devices OFF, once the power drops below DOWN value (parameter 21)
3	turn the associated devices ON, once the power rises above UP value (parameter 22)
4	turn the associated devices OFF, once the power rises above UP value (parameter 22)
5	combination of 1 and 4. Turn the associated devices ON, once the power drops below DOWN value (parameter 21). Turn the associated devices OFF, once the power rises above UP value (parameter 22).
6	combination of 2 and 3. Turn the associated devices OFF, once the power drops below DOWN value (parameter 21). Turn the associated devices ON, once the power rises above UP value (parameter 22).

Parameter 24: SWITCH ON value - On/Off association groups

The value of BASIC SET command frame sent to the devices associated in On/Off association groups (2, 3).On/Off (Button) association group - in accordance with parameter 20.On/Off (Power) association group - in accordance with parameter 23.
Size: 2 Byte, Default Value: 255

Setting	Description
0 - 99	sent value
255	sent value

Parameter 3: Overload safety switch

This function allows to turn off the controlled device in case of exceeding the defined power. Controlled device will be turned off even if Always On function is active (parameter 1).Controlled device can be turned back on via B-button or sending a control frame. By default this function is inactive.CAUTION! - The device has a protection that will turn the load off in the case of detecting current greater than 110% of rated current (>12A). It is a safety function and it cannot be turned off. After its activation the load can be turned on back again by pressing the B-button or sending a control frame. This function is independent of overload safety switch set in the parameter no. 3.
Size: 2 Byte, Default Value: 0

Setting	Description
0	function inactive
10 - 30000	(1.0 - 3000.0 W, step 0.1 W) - power threshold

Parameter 30: Active alarms

Define Z-Wave network alarms to which Plug-Control will respond.
Size: 1 Byte, Default Value: 63

Setting	Description
1	general alarm
0	no alarm
2	smoke alarm
4	CO alarm
8	CO2 alarm
16	high temperature alarm
32	flood alarm
63	all alarms

Parameter 31: Response to alarm frames

This parameter defines how Plug-Control will respond to alarms (devices status change).In case of values 1 or 2 Plug-Control is operating normally and LED ring signals an alarm through time defined in parameter 32 or until the alarm is cancelled.In case of values 5 to 50 Plug-Control does not report status change, power changes, ignores BASIC SET command frames. After time defined in parameter 32 or after the alarm cancellation, connected device is set to the previous state.
Size: 1 Byte, Default Value: 0

Setting	Description
0	no reaction
1	turn connected device on
2	turn connected device off
5 - 50	(0.5 - 5.0 s, step 0.1 s) - cyclically change device state with set period

Parameter 32: Alarm state duration

This parameter specifies the duration of alarm state. If a device sending an alarm frame through the Z-Wave network sets alarm duration as well, this settings are ignored.
Size: 2 Byte, Default Value: 600

Setting	Description
1 - 32400	in seconds

Parameter 40: Power load for violet colour

This parameter determines maximum active power value, which when exceeded, causes the LED ring flash violet. Function is active only when parameter 41 is set to 1 or 2.
Size: 2 Byte, Default Value: 25000

Setting	Description
1000 - 30000	100.0 - 3000.0 W, step 0.1 W

Parameter 41: LED ring colour when controlled device is on

When set to 1 or 2, LED ring colour will change depending on active power and parameter 40. Other colours are set permanently and do not depend on power consumption.
Size: 1 Byte, Default Value: 1

Setting	Description
0	illumination turned off completely
1	colour changes continuously depending on active power
2	colour changes in steps depending on active power
3	white
4	red
5	green
6	blue
7	yellow
8	cyan
9	magenta

Parameter 42: LED ring colour when controlled device is off

This parameter defines the illumination colour after turning off.
Size: 1 Byte, Default Value: 0

Setting	Description
0	illumination turned off completely
1	LED ring is illuminated with a colour corresponding to the last measured power, before the controlled device was turned off
3	white
4	red
5	green
6	blue
7	yellow
8	cyan
9	magenta

Parameter 43: LED ring colour at the Z-Wave network alarm detection

This parameter defines the illumination colour in case of Z-Wave alarm.
Size: 1 Byte, Default Value: 2

Setting	Description
0	illumination turned off completely
1	no change in colour. LED ring colour is determined by settings of parameters 41 or 42
2	LED ring flashes red/blue/white
3	white
4	red
5	green
6	blue
7	yellow
8	cyan
9	magenta

Parameter 50: Associations in Z-Wave network security mode

This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. This parameter does not apply to 1st Lifeline group.
Size: 1 Byte, Default Value: 3

Setting	Description
0	none of the groups sent as secure
1	2nd group sent as secure
2	3rd group sent as secure
3	2nd and 3rd group sent as secure

Technical Data