Ness
Ness Z-Wave Smart Plug
SKU: ZA-216001
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Smart plug is a Z-Wave Switch plugin module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1: Lifeline Group |
Configuration Parameters
Parameter 151: Threshold of power report
Set the power threshold. When the load power value exceeds this threshold, the smart plug will send a power report to the associated device (Lifeline Group). Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 200 | Available values: 0 - 200 (0 - 200W) |
| 0 | 0 - The function is disabled. |
Parameter 152: Percentage threshold for power reporting
Set the power percentage threshold. When the load power percentage value exceeds this threshold, the smart plug will send a power report to the associated device (Lifeline Group). Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 0 - 100 | Available values: 0 - 100 (0 - 100%) |
Parameter 171: Frequency of power reports
Defines how often power reports are sent to associated devices (Lifeline Group). Size: 4 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 3600 - 2678400 | Available values: 3600- 2678400 (3600 - 2678400s) |
Parameter 172: Frequency of energy reports
Defines how often energy reports are sent to associated devices (Lifeline Group). Size: 4 Byte, Default Value: 7200
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 3600 - 2678400 | Available values: 3600- 2678400 (3600 - 2678400s) |
Parameter 173: Frequency of voltage reports
Defines how often voltage reports are sent to associated devices (Lifeline Group). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 3600 - 2678400 | Available values: 3600- 2678400 (3600 - 2678400s) |
Parameter 174: Frequency of electric current reports
Defines how often electric current reports are sent to associated devices (Lifeline Group). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 3600 - 2678400 | Available values: 3600- 2678400 (3600 - 2678400s) |
Parameter 20: Overload protection
Smart Plug keep detecting the load power, once the AC current exceeds 11.5A for more than 5s, smart plug's relay will turn off. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled |
| 1 | The function is enabled. |
Parameter 21: Device state after power on
Defines the state of the plug when the power is turned on. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The Smart Plug will remain in the same state as it was before the power off. |
| 1 | The smart plug is turned on by default. |
| 2 | The smart plug is turned off by default. |
Parameter 24: Send reports when load status changes
Defines whether to send report to the associated device (Lifeline Group) when the load status of the Smart Plug changes. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled. |
| 1 | Send Basic report. |
| 2 | Send Basic report only when Load condition is not changed by Z-WAVE Command. |
Parameter 254: Enable/Disable the configuration command
Enable:The values of other parameters can be changed.Disable:The values of other parameters cannot be changed. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Enable |
| 1 | Disable |
Parameter 27: The state of indicator light
Define the corresponding state of the indicator light when the load changes. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The indicator light remains the same as the load on/off status. When the load is on, the light is on. When the load is off, the light is off. |
| 1 | Within 5 seconds after the operation load, the indicator light is consistent with the load on/off status, and then the indicator turns off. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.02 |
| Z-Wave Version | 6.81.01 |
| Certification ID | ZC10-22017070 |
| Z-Wave Product Id | 0x0208.0x0102.0x0029 |
| Firmware Updatable | |
| Supported Meter Type | |
| Neutral Wire Required | ok |
| Switch Type | |
| Color | |
| Communications Protocol | |
| Electric Load Type | |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |