iDevices
In-Wall Smart Dimmer
SKU: 61303/ZW3010
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Z-Wave PlusIn-Wall Smart Dimmer replaces existing light switch and allows remote control from any Z-Wavecertified hub.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Association Group 1 (Lifeline) supports Device Reset Locally and receives unsolicited status updates. |
| 2 | 5 | Association Group 2 supports Basic Set and is controlled by single pressing the button. |
| 3 | 5 | Association Group 3 supports Basic Set and is controlled by double pressing the button |
Configuration Parameters
Parameter 16: Switch Mode
Switch Mode Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable- Normal Operation |
| 1 | Press two times ON button and two times OFF button, LED will flash 5 times if device is successfully excluded. |
Parameter 19: Alternate Exclusion
Alternate Exclusion Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Normal Operation, press any button to exclude device |
| 1 | Press two times ON button and two times OFF button, LED will flash 5 times if device is successfully excluded. |
Parameter 3: LED Indication
LED Indication Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Device is ON, LED is OFF; device is Off, LED is ON |
| 1 | Device is ON, LED is ON; device is Off, LED is OFF |
| 2 | LED always OFF |
| 3 | LED always ON |
Parameter 30: Minimum Dim Threshold
Minimum Dim Threshold Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 99 | Set the minimum dimmer threshold when manually or remotely controlled |
Parameter 31: Maximum Brightness Threshold
Maximum Brightness Threshold Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 - 99 | Set the maximum brightness threshold when manually or remotely controlled |
Parameter 32: Default Brightness Level
Default Brightness Level Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Default |
| 1 - 99 | Ex. 1= 1% and 99 = 99% |
Parameter 6: Dim Up/Down Rate
Dim Up/Down Rate Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Dim up/down the light to the specified level quickly by command except value 0 and FF |
| 1 | Dim up/down the light to the specified level slowly by command except value 0 and FF |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.55 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-21107056 |
| Z-Wave Product Id | 0x0458.0x4944.0x3236 |
| Neutral Wire Required | ok |
| Electric Load Type | |
| Firmware Updatable | |
| Switch Type | |
| Z-Wave Scene Type | |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |