Sunricher
Thermostat-Heating
SKU: SR-ZV9092A-EU
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Product features: OLED display and touch buttons also as remote control other thermostatsfor heating Internal sensor for room temperature , externalInternal sensor for floor temperature Max Load 3680W @ 230V (resistive load),16A Alarm: over current, room temperature over heat Electric power measurement Internal overheatingprotection
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Lifelinesame main report |
| 2 | 5 | Transfer Command Class THERMOSTAT_SETPOINT_SET THERMOSTAT_MODE_SET to control other Thermostatwhen operationchanges |
Configuration Parameters
Parameter 10: Parameter 10
Temperature control reference selection Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | room sensor |
| 2 | floor sensor |
| 3 | room+floor sensor |
Parameter 11: Parameter 11
ROOM SENSOR temperature compensation setting,unit is 0.5 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -10 - 10 | value is-5~5 |
Parameter 12: Parameter 12
FLOOR SENSOR temperature compensation setting,unit is 0.5 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -10 - 10 | value is -5~5 |
Parameter 13: Parameter 13
Set how long the drying mode lasts, unit is minute Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 5 - 100 | value is5~100 minutes |
Parameter 14: Parameter 14
Set the mode after the drying mode ends Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | OFF |
| 1 | Manual mode (comfort mode) |
| 2 | Auto mode (energy save mode) |
| 3 | Away mode |
Parameter 16: Parameter 16
When to report temperature relative change threshold value actively, unit is 0.1 Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | disable to report |
| 2 - 10 | report when the threshold value is 0.2 - 1 |
Parameter 17: Parameter 17
Time interval value for periodic report of temperature, humidity, unit is S. Size: 2 Byte, Default Value: 300
| Setting | Description |
|---|---|
| 0 | disable to report |
| 30 - 28800 | report when time interval value is 30~28800 s |
Parameter 18: Parameter 18
When to report power change absolute threshold, unit is W Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | disable to report |
| 1 - 100 | report when absolute threshold is 1W~100W |
Parameter 19: Parameter 19
When to report current change absolute threshold, unit is 0.1A Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 | disable to report |
| 1 - 10 | report when absolute threshold is 0.1A~1A |
Parameter 2: Parameter 2
Over current detection max. value, unit is A. When detected current is over thisvalue, the device will turn off the relay and send NOTIFICATION CC. Size: 1 Byte, Default Value: 16
| Setting | Description |
|---|---|
| 0 | disable over current detection |
| 5 - 16 | over current detection max value |
Parameter 20: Parameter 20
When to report voltage change absolute threshold, unit is 1 V Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | disable to report |
| 1 - 10 | report when absolute threshold is 1~10 V |
Parameter 21: Parameter 21
Time interval value for periodic active report of Meterunit is S Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 60 - 2678400 | value is60~2678400 s |
Parameter 22: Parameter 22
The OLED display brightness when operate the device. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 2 | low levelmid levelhigh level |
Parameter 23: Parameter23
is parameter defines which sensor temperature will be displayed on Home page Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | indoor air temperature |
| 1 | external temperature (floor temperature) |
Parameter 24: Parameter 24
The time zone that the time parameters command adopts is UTC the time zone need to be set. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -12 - 12 | value is-12~12 |
Parameter 26: Parameter 26
Window open detect function temperature threshold: the Celsius degrees that the temperature decreases within 3 minutes, unit is 0.1 Celsius degree. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | disbaled |
| 15 - 40 | the set temperature threshold |
Parameter 3: Parameter 3
Vibration level triggered by pressing buttons Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable vibration and buzzer |
| 1 | Low Level |
| 2 | High Level |
Parameter 4: Parameter 4
Whether to recover to settings before power failure or power reset. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | use default settings |
| 1 | recover to settings before power failure or power reset |
Parameter 6: Parameter 6
High temperature detection max. value, unit is , when either temperature sensor is higher than this value, the device will turn off the relay and send NOTIFICATION CC. Size: 1 Byte, Default Value: 45
| Setting | Description |
|---|---|
| 0 | disable this function |
| 20 - 60 | air temperature over value |
Parameter 7: Parameter 7
Temperature control hysteresis value setting, setting range 0.5-2,unit is 0.1 Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 5 - 20 | hysteresis value0.5~2 |
Parameter 8: Parameter 8
Auto mode (Energy save mode) temperature schedule. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | use schedule set by user |
| 1 | use Energy_Save_Heating temperature set by THERMOSTAT_SETPOINT_SET |
Parameter 9: Parameter 9
Select floor temperature sensor type Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | NTC/10K B(25/50)=3950 |
| 2 | NTC/15K B(25/50)=3950 |
| 3 | NTC/50K B(25/50)=3950 |
| 4 | NTC/100K B(25/50)=3950 |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Thermostat - HVAC |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.24 |
| Z-Wave Version | 6.82.00 |
| Certification ID | ZC10-21097049 |
| Z-Wave Product Id | 0x0330.0x0200.0xD013 |
| Thermostat Power Source | |
| Thermostat HVAC Systems Supported | Heat Only |
| Thermostat Modes | Auto Changeover |
| Electric Load Type | |
| Firmware Updatable | Not Updatable |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |