On/Off Switch (Red Series)

Parameter 1: Power On State

When power is restored, the switch reverts to either On, Off, or Last Level.
Size: 1 Byte, Default Value: 0

Setting	Description
0	When Power is restored, switch returns to state prior to power outage
1	When Power is restored, switch turns ON
2	When Power is restored, switch is OFF

Parameter 10: Active Power Alerts

The power level change that will result in a new power report being sent (% of previous report). Example of how the values work: 0 = Disabled, 10 = 10% of previous report, 100 = 100% of previous report.
Size: 1 Byte, Default Value: 10

Setting	Description
0	Disabled
1 - 100	Percentage of previous report

Parameter 11: Periodic Power + Energy Reports

Time period between consecutive power and energy reports being sent (in seconds). Example of how the values work: 0 = 0 seconds, 1 = 1 second, 32767 = 32767 seconds. The timer resets after every report is sent.
Size: 2 Byte, Default Value: 3600

Setting	Description
0 - 32767	Seconds

Parameter 12: Energy Reports

The energy level change that will result in a new energy report being sent (% of previous report). Example of how the values work: 0 = Disabled, 10 = 10% of previous report, 100 = 100% of previous report.
Size: 1 Byte, Default Value: 10

Setting	Description
0	Disabled
1 - 100	Percentage of previous report

Parameter 2: Invert Switch

Inverts the switch (Tap Down = On, Tap Up = Off). Example of how the values work: 0 = Disabled, 1 = Enabled. This parameter can be set without a HUB from the Configuration Button.
Size: 1 Byte, Default Value: 0

Setting	Description
0	Disabled
1	Enabled

Parameter 3: Auto Off Timer

Automatically turns the switch off after x amount of seconds. Example of how the values work: 0 = Disabled, 1 = 1 second, 32767 = 32767 seconds.
Size: 2 Byte, Default Value: 0

Setting	Description
0	Disabled
1 - 32767	Seconds

Parameter 4: Association Behavior

When should the switch send commands to associated devices.
Size: 1 Byte, Default Value: 15

Setting	Description
1	Local
2	3-Way
3	3-Way + Local
4	Z-Wave HUB
5	Z-Wave HUB + Local
6	Z-Wave HUB + 3-Way
7	Z-Wave HUB + Local
8	Timer
9	Timer + Local
10	Timer + 3-Way
11	Timer + Local
12	Timer + Z-Wave HUB
13	Timer + Local
14	Timer + Z-Wave HUB
15	All

Parameter 5: LED Indicator Color

This will set the default color of the LED Bar. This is calculated by using a hue color circle (Value / 255 * 360). See website for more info. This parameter can be set without a HUB from the Configuration Button.
Size: 2 Byte, Default Value: 170

Setting	Description
0 - 255	Hue Color Circle
170	Blue

Parameter 51: Disable 700ms Delay

Disables the 700ms delay. Note, if you disable the delay, it will also disable scene control except for Button 1 (ie: tap up 1x or tap down 1x) and button 7 (config button). All other buttons (2-6) will be disabled.
Size: 1 Byte, Default Value: 1

Setting	Description
0	700ms Delay Disabled
1	700ms Delay Enabled

Parameter 6: LED Indicator Intensity

This will set the intensity of the LED bar (ie: how bright it is). Example of how the values work: 0 = Off, 1 = Low, 5 = Medium, 10 = High. This parameter can be set without a HUB from the Configuration Button.
Size: 1 Byte, Default Value: 5

Setting	Description
0	Off
1 - 3	Low Intensity
4 - 7	Medium Intensity
8 - 10	High Intensity

Parameter 7: LED Indicator Intensity (When Off)

This is the intensity of the LED bar when the switch is off. Example of how the values work: 0 = Off, 1 = Low, 5 = Medium, 10 = High. This parameter can be set without a HUB from the Configuration Button.
Size: 1 Byte, Default Value: 1

Setting	Description
0	Off
1 - 3	Low Intensity
4 - 7	Medium Intensity
8 - 10	High Intensity

Parameter 8: LED Strip Effect

This will allow you to add some sweet effects to your LED bar (ie: pulse, chase, solid, etc). Example of how the values work: Byte 1 = Choose Color, Byte 2 = Choose Brightness Level, Byte 3 = Choose Effect, Byte 4 = Duration. Please see website for further instructions on how to set this up as the possible values are a matrix. You start with Byte 1 to select the color, then move to Byte 2 to select the Brightness Level, then move to Byte 3 to choose the Effect, and finally move to Byte 4 to choose the Duration.
Size: 4 Byte, Default Value: 0

Setting	Description
0	Please see website for matrix - https://nathanfiscus.github.io/inovelli-notification-calc/

Technical Data