.png){kind=logo}
Qubino (Goap)
Luxy Smart Light
SKU: GOAEZMNHQD1
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Luxy Smart Light is an innovative light source that gently illuminates in more than 16 million colours and easily fits into places of your light switch or socket. It can be used standalone, as ambient light, or as a smart home device. With an integrated beeper, it enables a unique combination of sound and visual notifications. It can be controlled with a touch on one of the 4 sides on the touch-sensitive surface (or touch screen) or remotely via a smartphone. It can be set to work automatically, according to the pre-programmed scenes, created on the Z-Wave gateway. Set the Luxy Smart Light as a visual alarm, for a gentle wake-up, with colours simulating the sunrise or illuminate your corridor in the night-time, so you dont have to turn on the main light or stumble in the dark.
Installation
As a smart light
Connected to a switch
NOTE: Antenna positioning
Product Usage
1. Turns ON/OFF the Luxy light Dims the Luxy light
2. Switches between 4 different lighting effects (ocean, sunrise, rainbow, and nature)
3. Turns ON/OFF the white light on the Luxy Dims the Luxy light
4. Starts the colour spectrum and stops at the colour you wish to have
| Reset to factory default | 1. Connect the device to the power supply.
2. Press once on button 2 - right.
3. One press on button 3 - down for enabling full white. 4. When full white is enabled, press, and hold button 4 - left for 10 seconds. After 10 seconds, the device starts flashing blue 1 second on, 0.5 second off. 5. After 10 seconds the device stops flashing and turns full blue. |
| Inclusion | 1. Press once on button 2 - right. 2. One press on button 3 - down for enabling full white. 3. When full white is enabled, press, and hold button 2 - right, between 4 and 6 seconds. After 6 seconds, the device starts flashing green (1 second ON, 0.5 second OFF). Once the device receives node ID (after 10 seconds), it stops flashing and turns full green. The procedure is always available. |
| Exclusion | 1. Press once on button 2 - right. 2. One press on button 3 - down for enabling full white. 3. When full white is enabled, press, and hold button 2 - right for 5 seconds. After 5 seconds, the device starts flashing red 1 second ON, 0.5 second OFF. Once the device loses node ID (after 10 seconds), it stops flashing and turns full red. The procedure is always available. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Lifeline |
| 2 | 5 | ON/OFF (Basic Set |
| 3 | 5 | Dim (Multilevel) |
| 4 | 5 | Change of color (Switch Color) |
Configuration Parameters
Parameter 1: Digital input type
Defines the input type of device connected to digital input. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Push-button |
| 1 | ON/OFF toggle switch |
| 2 | Motion sensor |
| 3 | Motion sensor with memory (turned off after certain amount of time defined in parameter 5) |
Parameter 3: Turning off alarming
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | only by z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, sound switch play tone, sound switch configuration, switch color set, switch color start/stop level change, notification report idle) |
| 1 | capacitive input or z-wave command (basic set, switch multilevel set, switch multilevel start/stop level change, sound switch play tone, sound switch configuration, switch color set, switch color start/stop level change, notification report idle) |
Parameter 5: Motion sensor memory timer
Defines the time after which the output triggered by motion sensor is turned off. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 32534 | 0-32534 seconds after which the LED will be turned off. |
| 32535 | never turns off |
Parameter 10: Auto on timer
Defines the time after which the device is turned to last known state. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | disabled |
| 30 - 32353 | seconds after which the device turns on |
Parameter 11: Auto off timer
Defines the time after which the device is turned to last known state. Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 0 | disabled |
| 30 - 32535 | seconds after which the device turns off |
Parameter 30: Restore state on power failure
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disabled (the device will not restore state on power failure and will remain off) |
| 1 | enabled (the device will restore state on power failure) |
Parameter 50: Beeper enable/disable
This parameter affects beeper function just in case when the device receives the NOTIFICATION_REPORT. If the user sends a SOUND_SWITCH_TONE_PLAY_SET (1), the buzzer still emits a serviceable tone. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disabled (the beeper is not active) |
| 1 | enabled (the beeper is active) |
Technical Data
| Dimensions | 93 x90 x 48 mm |
| Weight | 141 gr |
| Hardware Platform | ZM5101 |
| EAN | 3830062071796 |
| IP Class | IP 20 |
| Voltage | 230V |
| Device Type | Color Switch |
| Network Operation | Always On Slave |
| Z-Wave Version | 6.82.00 |
| Certification ID | ZC10-20096982 |
| Z-Wave Product Id | 0x0159.0x0008.0x0051 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |