ABUS
Nexello Outdoor Siren
SKU: PLSG10100
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Fire, breaking and entering or tampering: The ABUS Nexello outdoor siren for protected outdoor areas will sound the alarm at over 100 dB in all cases. On request in addition to or exclusively visually via a red LED.The settings for alarm duration, volume and the siren LED can be flexibly configured.Is the alarm duration too long? Or want the LED of the outdoor siren to alert you of the enabling and disarming of the alarm system? Various parameters can be individually adjusted. The desired configuration is carried out in a few simple steps via ABUS Nexello.The outdoor siren can be operated completely 100% wirelessly using batteries or an external power supply and can be freely positioned using a wall bracket with a set of dowels and screws. It has a cover contact and wall contact as protection against tampering. The siren indicates an imminent battery replacement or power failure, via a push notification to the free Nexello app.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | The Lifeline Association is automatically established between the Z-Wave controller and the device at inclusion and defines what information is exchanged between the Z-Wave controller and the device. |
Configuration Parameters
Parameter 1: Alarm duration
Setting how long an alarm of the piezo siren lasts when triggered. Size: 2 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 5 - 600 | Adjustable from 5 - 600 in seconds |
Parameter 2: Alarm
Setting the reaction in case of an alarm. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | siren and LEDs / flash |
| 1 | Siren only |
| 2 | LEDs only / flash light |
Parameter 3: Siren volume
Adjusts the volume of the siren. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 100dB |
| 1 | 85dB |
Parameter 4: Sabotage Alarm
Defines whether an alarm should be triggered directly in the event of a sabotage alarm. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The siren does not automatically trigger an alarm, the sabotage alarm is triggered by the Z-Wave controller. This function is deactivated by default, because when activated, a sabotage alarm is always triggered directly by the siren, even if the Z-Wave controller/alarm system is in maintenance mode, for example. |
| 1 | The siren always triggers an alarm automatically, regardless of the status of the Z-Wave controller. Note: Sabotage Alarm will also be triggered while maintenance mode. |
Parameter 5: Status display
Setting whether only certain status events should be displayed. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | activation & deactivation |
| 1 | Only activation |
| 2 | Only deactivation |
| 3 | No activation & deactivation |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Siren |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.01:00.03 |
| Z-Wave Version | 6.82.00 |
| Certification ID | ZC10-20096975 |
| Z-Wave Product Id | 0x0403.0x0003.0x0008 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |