ABUS
Nexello 3I/3O Hybrid Module
SKU: PLHA10100
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The module is mounted via a bracket, it is tamper protected and has a back-up battery.Three Inputs for the connection of: Analogue sensors with voltage 0~12VDigital sensors with voltage 0~12VPotential-free outputs NC/NOOpen Collector Outputs OCThree Outputs for connecting actuators with a maximum of 24VDCSPDT (Single Pole, Double Throw) relay (toggle switch)functions:Configurable timer that automatically switches off after a preset period of time (default is 500 ms)The output can be set to activate automatically when the input terminals (see configuration setting)
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | The Lifeline Association is automatically established between the Z-Wave controller and the device at inclusion and defines what information is exchanged between the Z-Wave controller and the device. |
| 2 | 5 | When a signal input is triggered, the unit first sends a BASIC Set ON. When the preset timer expires, it sends a BASIC Set OFF. |
| 3 | 5 | When a signal input is triggered, the unit first sends a BASIC Set ON. When the preset timer expires, it sends a BASIC Set OFF. |
| 4 | 5 | When a signal input is triggered, the unit first sends a BASIC Set ON. When the preset timer expires, it sends a BASIC Set OFF. |
Configuration Parameters
Parameter 1: Signal input 1 - Mode
Several settings of the signal input and its triggering behaviour. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | No Relay is triggered, No Voltage is present, triggers below lowthreshold |
| 2 - 0 | Relay 1 is triggered, No Voltage is present, triggers below lowthreshold |
| 4 - 0 | Relay 2 is triggered, No Voltage is present, triggers below lowthreshold |
| 6 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers below lowthreshold |
| 8 - 0 | Relay 3 is triggered, No Voltage is present, triggers below lowthreshold |
| 10 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 14 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 64 - 0 | No Relay is triggered, 3,3V is present, triggers below lowthreshold |
| 66 - 0 | Relay 1 is triggered, 3,3V is present, triggers below lowthreshold |
| 68 - 0 | Relay 2 is triggered, 3,3V is present, triggers below lowthreshold |
| 70 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers below lowthreshold |
| 72 - 0 | Relay 3 is triggered, 3,3V is present, triggers below lowthreshold |
| 74 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 78 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 128 - 0 | No Relay is triggered, No Voltage is present, triggers above highthreshold |
| 130 - 0 | Relay 1 is triggered, No Voltage is present, triggers above highthreshold |
| 132 - 0 | Relay 2 is triggered, No Voltage is present, triggers above highthreshold |
| 134 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers above highthreshold |
| 136 - 0 | Relay 3 is triggered, No Voltage is present, triggers above highthreshold |
| 138 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 142 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 192 - 0 | No Relay is triggered, 3,3V is present, triggers above highthreshold |
| 194 - 0 | Relay 1 is triggered, 3,3V is present, triggers above highthreshold |
| 196 - 0 | Relay 2 is triggered, 3,3V is present, triggers above highthreshold |
| 198 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers above highthreshold |
| 200 - 0 | Relay 3 is triggered, 3,3V is present, triggers above highthreshold |
| 202 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 206 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 12 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 76 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 140 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 204 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
Parameter 10: Signal input 2 - voltage low-threshold
Setting of the voltage drop below which the signal input is triggered Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (10 = 1000mV = 1.0V) |
Parameter 11: Signal input 3 - Mode
Same as Parameter 1, but applies to Signal Input 3 Size: 1 Byte, Default Value: 64
| Setting | Description |
|---|---|
| 0 | No Relay is triggered, No Voltage is present, triggers below lowthreshold |
| 2 - 0 | Relay 1 is triggered, No Voltage is present, triggers below lowthreshold |
| 4 - 0 | Relay 2 is triggered, No Voltage is present, triggers below lowthreshold |
| 6 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers below lowthreshold |
| 8 - 0 | Relay 3 is triggered, No Voltage is present, triggers below lowthreshold |
| 10 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 12 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 14 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 64 - 0 | No Relay is triggered, 3,3V is present, triggers below lowthreshold |
| 66 - 0 | Relay 1 is triggered, 3,3V is present, triggers below lowthreshold |
| 68 - 0 | Relay 2 is triggered, 3,3V is present, triggers below lowthreshold |
| 70 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers below lowthreshold |
| 72 - 0 | Relay 3 is triggered, 3,3V is present, triggers below lowthreshold |
| 74 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 76 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 78 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 128 - 0 | No Relay is triggered, No Voltage is present, triggers above highthreshold |
| 130 - 0 | Relay 1 is triggered, No Voltage is present, triggers above highthreshold |
| 132 - 0 | Relay 2 is triggered, No Voltage is present, triggers above highthreshold |
| 134 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers above highthreshold |
| 136 - 0 | Relay 3 is triggered, No Voltage is present, triggers above highthreshold |
| 138 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 140 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 142 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 192 - 0 | No Relay is triggered, 3,3V is present, triggers above highthreshold |
| 194 - 0 | Relay 1 is triggered, 3,3V is present, triggers above highthreshold |
| 196 - 0 | Relay 2 is triggered, 3,3V is present, triggers above highthreshold |
| 198 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers above highthreshold |
| 200 - 0 | Relay 3 is triggered, 3,3V is present, triggers above highthreshold |
| 202 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 204 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 206 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
Parameter 12: Relay output 3 - switching time
Setting for the duration of the switching time when the relay output is switched. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | relay output is permanently switched |
| 1 - 255 | Adjustable duration from 1 - 255 in 100ms steps |
Parameter 13: Signal input 3 - switching time at association group 4
Setting for the duration of the switching time at association group 4 when signal input is triggered. Size: 1 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 0 | Switched permanently |
| 1 - 255 | Adjustable duration from 1 - 255 in seconds |
Parameter 14: Signal input 3 - voltage high-threshold
Setting, from which voltage rise the signal input is triggered Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (25 = 2500mV = 2.5V) |
Parameter 15: Signal input 3 - voltage low-threshold
Setting of the voltage drop below which the signal input is triggered Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (10 = 1000mV = 1.0V) |
Parameter 16: Voltage Report (time)
The interval time of the voltage report for signal input 1-3 Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 255 | Adjustable from 1 - 255 in minutes |
Parameter 17: Sabotage Alarm Relay output
Setting whether a relay output must be switched in case of a sabotage alarm. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | No Relays are triggered |
| 2 - 0 | Relay 1 is triggered |
| 4 - 0 | Relay 2 is triggered |
| 6 - 0 | Relay 1 and 2 are triggered |
| 8 - 0 | Relay 3 is triggered |
| 10 - 0 | Relay 1 and 3 are triggered |
| 12 - 0 | Relay 2 and 3 are triggered |
| 14 - 0 | Relay 1, 2 and 3 are triggered |
Parameter 18: Signal input - Activate arm / disarm message
Setting whether a signal input should send an armed and an unarmed message instead of a trigger signal. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | 0 = No signal input sends arm/disarm message |
| 1 | 1 = Signal input 1 sends arm/disarm message |
| 2 | 2 = Signal input 2 sends arm/disarm message |
| 3 | 3 = Signal input 3 sends arm/disarm message |
Parameter 2: Relay output 1 - switching time
Setting for the duration of the switching time when the relay output is switched. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | relay output is permanently switched |
| 1 - 255 | Adjustable duration from 1 - 255 in 100ms steps |
Parameter 3: Signal input 1 - switching time at association group 2
Setting for the duration of the switching time at association group 2 when signal input is triggered. Size: 1 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 0 | Switched permanently |
| 1 - 255 | Adjustable duration from 1 - 255 in seconds |
Parameter 4: Signal input 1 - voltage high-threshold
Setting, from which voltage rise the signal input is triggered Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (25 = 2500mV = 2.5V) |
Parameter 5: Signal input 1 - voltage low-threshold
Setting of the voltage drop below which the signal input is triggered Size: 1 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (10 = 1000mV = 1.0V) |
Parameter 6: Signal input 2 - Mode
Same as Parameter 1, but applies to Signal Input 2 Size: 1 Byte, Default Value: 64
| Setting | Description |
|---|---|
| 0 | No Relay is triggered, No Voltage is present, triggers below lowthreshold |
| 2 - 0 | Relay 1 is triggered, No Voltage is present, triggers below lowthreshold |
| 4 - 0 | Relay 2 is triggered, No Voltage is present, triggers below lowthreshold |
| 6 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers below lowthreshold |
| 8 - 0 | Relay 3 is triggered, No Voltage is present, triggers below lowthreshold |
| 10 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 12 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 14 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers below lowthreshold |
| 64 - 0 | No Relay is triggered, 3,3V is present, triggers below lowthreshold |
| 66 - 0 | Relay 1 is triggered, 3,3V is present, triggers below lowthreshold |
| 68 - 0 | Relay 2 is triggered, 3,3V is present, triggers below lowthreshold |
| 70 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers below lowthreshold |
| 72 - 0 | Relay 3 is triggered, 3,3V is present, triggers below lowthreshold |
| 74 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 76 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 78 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers below lowthreshold |
| 128 - 0 | No Relay is triggered, No Voltage is present, triggers above highthreshold |
| 130 - 0 | Relay 1 is triggered, No Voltage is present, triggers above highthreshold |
| 132 - 0 | Relay 2 is triggered, No Voltage is present, triggers above highthreshold |
| 134 - 0 | Relay 1 and 2 are triggered, No Voltage is present, triggers above highthreshold |
| 136 - 0 | Relay 3 is triggered, No Voltage is present, triggers above highthreshold |
| 138 - 0 | Relay 1 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 140 - 0 | Relay 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 142 - 0 | Relay 1, 2 and 3 are triggered, No Voltage is present, triggers above highthreshold |
| 192 - 0 | No Relay is triggered, 3,3V is present, triggers above highthreshold |
| 194 - 0 | Relay 1 is triggered, 3,3V is present, triggers above highthreshold |
| 196 - 0 | Relay 2 is triggered, 3,3V is present, triggers above highthreshold |
| 198 - 0 | Relay 1 and 2 are triggered, 3,3V is present, triggers above highthreshold |
| 200 - 0 | Relay 3 is triggered, 3,3V is present, triggers above highthreshold |
| 202 - 0 | Relay 1 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 204 - 0 | Relay 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
| 206 - 0 | Relay 1, 2 and 3 are triggered, 3,3V is present, triggers above highthreshold |
Parameter 7: Relay output 2 - switching time
Setting for the duration of the switching time when the relay output is switched. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | relay output is permanently switched |
| 1 - 255 | Adjustable duration from 1 - 255 in 100ms steps |
Parameter 8: Signal input 2 - switching time at association group 3
Setting for the duration of the switching time at association group 3 when signal input is triggered. Size: 1 Byte, Default Value: 180
| Setting | Description |
|---|---|
| 0 | Switched permanently |
| 1 - 255 | Adjustable duration from 1 - 255 in seconds |
Parameter 9: Signal input 2 - voltage high-threshold
Setting, from which voltage rise the signal input is triggered Size: 1 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 255 | Adjustable from 0 - 255 in 100mV steps (25 = 2500mV = 2.5V) |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00:00.04 |
| Z-Wave Version | 6.81.06 |
| Certification ID | ZC10-20076949 |
| Z-Wave Product Id | 0x0403.0x0003.0x0007 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |