This is a
ECO-DIM.10 Z-Wave is a smart module dimmer for LED lights. The dimmer module has a range of 250W LED and beside LED lights also able to dim 230V halogen and incandescent bulds, dimable LED-drivers and electronic transfomers.The minimum and maximum light level of the dimmer can be adjusted by the MIN and MAX potentiometer, also the speed of dimming by a pulse switch is adjustable by the SPEED potentiometer. The ECO-DIM.10 is protected against overload and interference signals.For the installation of the ECO-DIM.10 Z-Wave you only need two wires, three wire installation (with extra neutral wire) is available, but not required.It is suitable for all smarthome systems based on Z-Wave (plus) protocol. The smart dimmer module is compatible with 95% of all dimmable LED lights.
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | The ASSIC of Lifeline: 4C 69 66 65 6C 69 6E 651. When press and hold down Reset button for 4S to reset the dimmer, send u0022Device Reset Locally Notification CCu0022 to associated devices of this group to report factory reset information.2. When load state changes, send u0022Switch Multilevel Report CCu0022 to associated devices of this group. |
2 | 5 | Basic Set: 42 61 73 69 63 20 53 65 741. Short press the knob turn on the dimmer Sends Basic Set(0xFF) to associated devices2. Short press the knob turn off the dimmer Sends Basic Set(0x00) to associated devices |
3 | 5 | Switch Multilevel: 53 77 69 74 63 68 20 4D 75 6C 74 69 6C 65 76 65 6C1. Anti-Clockwise the knob Sends Switch Multilevel Set(to decrease the brightness and keep associated devices in sync with this device) to associated devices2. Clockwise the knob Sends Switch Multilevel Set(to increase the brightness and keep associated devices in sync with this device) to associated devices |
4 | 5 | External Button: 45 78 74 65 72 6E 61 6C 20 42 75 74 74 6F 6E1. External Button hold send Switch Multilevel Start Level Change (Switchover dimmer Up/Down)2. External Button release send Switch Multilevel Stop Level Change |
he state the switch should return to once power is restored after power failure.0 - Off.1 - On.2 - Returns to level before Power Outage Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Off |
1 | On |
2 | Returns to level before Power Outage |
The Dimmer will send notification to associated device (Group Lifeline)when the status ofDimmer load is changed. 0 - The function is disabled.1 - Send Switch Multilevel Report.2-Send Switch Multilevel Report only when Load status is not changed by Z-WAVE Command Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled |
1 | SendSwitch Multilevel Report . |
2 | SendSwitch Multilevel Report only when Load status is not changed by Z-WAVE Command |
Valid value, unit is second. 0-1000 - Instanly.1 - Fast.100 - Slow. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | instantly |
1 | fast |
100 | slow |
Enable or Disable external switch to pair network.0 - Disable.1 - Enable. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Setting dimming way.0 - Linear dimming.1 - Logarithmic dimming. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Linear dimming |
1 | Logarithmic dimming |
Setting default brightness when turn on the dimmer from off status. Setting of 0 means that the dimmer will use parameter 1.From 0; To: 99; Description: Default brightness percentage Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | the default brightness is 1% |
1 - 99 | Default brightness percentage (where 99% = 100% brightness) |
Setting delay time when turn off, unit is second. Values reads: From: 1; To: 60; Description: Amount of time in seconds after which the light turns off Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | the light turns off immediately |
1 - 60 | Amount of time in seconds after which the light turns off |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.10 |
Z-Wave Version | 6.81.03 |
Certification ID | ZC10-20076947 |
Z-Wave Product Id | 0x0431.0x0202.0x0002 |
Switch Type | Decorator Paddle Push |
Firmware Updatable | Updatable by Consumer by RF |
Communications Protocol | Manufacturer Proprietary Protocol |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |