This is a
Smart Plug is a Z-Wave Switch plugin module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report wattage consumption or kWh energy usage. This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave Plus messages to communicate to other security enabled Z-Wave Plus products.Smart Plug is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.This device must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize all implemented functions.Features:1) AC output switch on/off by manual or Z-Wave command;2) RGB LED indicates the Z-WAVE network range and load power;3) Support S0 and S2 security network;4) Supporting power meter;5) Supporting repeater role;6) Supporting firmware OTA;7) Supporting Smart Start;8) Supports over-current protection
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
Power threshold to be interpreted, when the change value of load power exceeds the setting threshold, the smart plug will send meter report to association device (Group Lifeline). Size: 2 Byte, Default Value: 50
Setting | Description |
---|---|
0 - 200 | Available settings: 0 - 200 (0 - 200W) |
0 | 0 - The function is disabled. |
Power percentage threshold to be interpreted, when change value of the load power exceeds the setting threshold, the smart plug will send meter report to association device (Group Lifeline). Size: 1 Byte, Default Value: 10
Setting | Description |
---|---|
0 | The function is disabled. |
1 - 100 | Available settings: 1- 100 (0 - 100%) |
The interval of sending power report to association device (Group Lifeline). Size: 4 Byte, Default Value: 3600
Setting | Description |
---|---|
0 | The function is disabled. |
3600 - 2678400 | Available settings: 3600- 2678400 (3600 - 2678400s) |
The interval of sending energy report to association device (Group Lifeline). Size: 4 Byte, Default Value: 7200
Setting | Description |
---|---|
0 | The function is disabled. |
3600 - 2678400 | Available settings: 3600- 2678400 (3600 - 2678400s) |
The interval of sending voltage report to association device (Group Lifeline). Size: 4 Byte, Default Value: 7200
Setting | Description |
---|---|
0 | The function is disabled. |
3600 - 2678400 | Available settings: 3600- 2678400 (3600 - 2678400s) |
The interval of sending electricity report to association device (Group Lifeline). Size: 4 Byte, Default Value: 7200
Setting | Description |
---|---|
0 | The function is disabled. |
3600 - 2678400 | Available settings: 3600- 2678400 (3600 - 2678400s) |
Smart Plug keep detecting the load power, once the AC current exceeds 11.5A for more than 5s, smart plug's relay will turn off. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled |
1 | The function is enabled. |
Define how the Plug reacts after the power supply is back on. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Smart Plug memorizes its state after a power failure. |
1 | Smart Plug does not memorize its state after a power failure. Connected device will be on after the power supply is reconnected. |
2 | Smart Plug does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected. |
Smart Plug can send notifications to association device (Group Lifeline) when state of smart plugs load change. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled. |
1 | Send Basic report. |
2 | Send Basic report only when Load condition is not changed by Z-WAVE Command. |
Lock/unlock all configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Unlock |
1 | Lock |
After smart plug being included into a Z-Wave network, the RGB LED indicator will indicator the situation of load. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | The indicator light remains the same as the load on/off status. When the load is on, the light is on, and the off is off. |
1 | Within 5 seconds after the operation load, the indicator light is consistent with the load on/off status, and then the indicator is off. |
Hardware Platform | ZM5202 |
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.02 |
Z-Wave Version | 6.81.01 |
Certification ID | ZC10-20076940 |
Z-Wave Product Id | 0x0208.0x0100.0x0019 |
Electric Load Type | |
Communications Protocol | Manufacturer Proprietary Protocol |
Firmware Updatable | Not Updatable |
Switch Type | Decorator Paddle Push |
Color | Antique Brass |
Supported Meter Type | |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |