HZC ELECTRIC
Smart Dimmer Module 5-250W
SKU: CFG-B5L
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The CFG-B5L is a module for controlling virtually any sort of lighting load.It can be used as a dimmer with dimmable LED, CFL, incandescent and halogen lighting. Besides it also supports energy monitoring when used with compatible automaton systems.The 19.8mm thick dimmer can be installed behind a standard wall switch in the junction box - Z-Wave Plus 500 series- Supports dimming operation for dimmable LED, CFL, incandescent and halogen - Installs behind your wall switch- Soft start dimming- Last light level memory- Min. & Max. brightness setting- Adjustable dimming step- Supports 3 wire and 2 wire (without neutral) installation- No Bypass required (At least 8W)- Dimensions: 40.5 x 40.5 x 19.80 mm (L x W x H)
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | The ASSIC of Lifeline: 4C 69 66 65 6C 69 6E 651. When press and hold down Reset button for 4S to reset the dimmer, send u0022Device Reset Locally Notification CCu0022 to associated devices of this group to report factory reset information.2. When load state changes, send u0022Switch Multilevel Report CCu0022 to associated devices of this group. |
| 2 | 5 | Basic Set: 42 61 73 69 63 20 53 65 741. Short press the knob turn on the dimmer Sends Basic Set(0xFF) to associated devices2. Short press the knob turn off the dimmer Sends Basic Set(0x00) to associated devices |
| 3 | 5 | Switch Multilevel: 53 77 69 74 63 68 20 4D 75 6C 74 69 6C 65 76 65 6C1. Anti-Clockwise the knob Sends Switch Multilevel Set(to decrease the brightness and keep associated devices in sync with this device) to associated devices2. Clockwise the knob Sends Switch Multilevel Set(to increase the brightness and keep associated devices in sync with this device) to associated devices |
| 4 | 5 | External Button: 45 78 74 65 72 6E 61 6C 20 42 75 74 74 6F 6E1. External Button hold send Switch Multilevel Start Level Change (Switchover dimmer Up/Down)2. External Button release send Switch Multilevel Stop Level Change |
Configuration Parameters
Parameter 1: State After Power Restored
he state the switch should return to once power is restored after power failure.0 - Off.1 - On.2 - Returns to level before Power Outage Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Off |
| 1 | On |
| 2 | Returns to level before Power Outage |
Parameter 2: Notification when Load status change
The Dimmer will send notification to associated device (Group Lifeline)when the status ofDimmer load is changed. 0 - The function is disabled.1 - Send Switch Multilevel Report.2-Send Switch Multilevel Report only when Load status is not changed by Z-WAVE Command Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | The function is disabled |
| 1 | SendSwitch Multilevel Report . |
| 2 | SendSwitch Multilevel Report only when Load status is not changed by Z-WAVE Command |
Parameter 3: Default dimming speed
Valid value, unit is second. 0-1000 - Instanly.1 - Fast.100 - Slow. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 | instantly |
| 1 | fast |
| 100 | slow |
Parameter 5: Enable or Disable external switch to pairnetwork
Enable or Disable external switch to pair network.0 - Disable.1 - Enable. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 6: Setting dimming way
Setting dimming way.0 - Linear dimming.1 - Logarithmic dimming. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Linear dimming |
| 1 | Logarithmic dimming |
Parameter 7: Setting default brightness when turn onthe dimmer from off status.
Setting default brightness when turn on the dimmer from off status. Setting of 0 means that the dimmer will use parameter 1.Valid value:0-99 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | the default brightness is 1% |
| 99 | the default brightness is 100% |
Parameter 8: Setting delay time when turn off
Setting delay time when turn off, unit is second. Valid value:0-60 Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | the light turns off immediately |
| 1 | the light turns off after 1s. |
| 60 | the light turns off after 60s. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.10 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-20076934 |
| Z-Wave Product Id | 0x0431.0x0202.0x0002 |
| Communications Protocol | Manufacturer Proprietary Protocol |
| Switch Type | Decorator Paddle Push |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |