Namron
DIMMER 2 400W
SKU: DIMMER 2 400W
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The micro smart dimmer is a Z-Wave device designed to work with various types of light sources. It may be connected to two-wire or three-wire configuration so it can operate with or without neutral lead. The dimmer can switch or dim connected light source either through Z-Wave devices or through the wall switch connected directly to it. The smart dimmer is equipped with an algorithm of smart light source detection which makes configuration easier and ensures high compatibility of the device. It may be usedas a switch with non-dimmable light sources (in 3-wire onnection).
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | 1. When press and hold down Reset button for 10S to reset the dimmer, send u0022Device Reset Locally Notification CCu0022 to associated devices of this group to report factory reset information.2. When load state changes, send u0022Basic Report CCu0022 to associated devices of this group.3. When a load over current is detected, send u0022Over-current detectedu0022 to Lifeline.4. When a mains voltage drop is detected, send u0022Voltage drop/driftu0022 to Lifeline.5. When over temperature is detected, send Emergency shutoff statusu0022 to Lifeline. |
Configuration Parameters
Parameter 11: Wiring type
Wiring typeNote: this parameter is read only Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | unknown |
| 1 | 2 Wire With No Neutral |
| 2 | 3 Wire With Neutral |
Parameter 12: Load type
Load typeNote: this parameter is read only Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | unknown |
| 1 | resistive |
| 2 | inductive |
| 3 | capacitive |
Parameter 13: Enable/disable over current protection
Enable/disable over current protection (over 1.5A for 20 seconds continuously) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable |
| 1 | enable |
Parameter 14: Power automatic report absolute threshold, unit is W
Power automatic report absolute threshold, unit is WWhen power changes above the absolutethreshold, immediately report current power value Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 0 - 32767 | When power changes above the absolute threshold, immediately report current power value |
Parameter 15: Power automatic report percentage threshold, unit is %
Power automatic report percentage threshold, unit is %When power changes above the percentage threshold, immediately report current power value Size: 1 Byte, Default Value: 20
| Setting | Description |
|---|---|
| 0 - 100 | When power changes above the percentage threshold, immediately report current power value |
Parameter 2: Saving load state before power failure
Saving load state before power failure Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | shutoff load |
| 1 | turn on load |
| 2 | save load state before power failure |
Parameter 21: Power metering automatic report time cycle, unit is second
Power metering automatic report time cycle, unit is second Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 5 - 2678400 | Power metering automatic report time cycle, unit is second |
Parameter 22: Energy metering automatic report time cycle, unit is second
Energy metering automatic report time cycle, unit is second Size: 4 Byte, Default Value: 1800
| Setting | Description |
|---|---|
| 5 - 2678400 | Energy metering automatic report time cycle, unit is second |
Parameter 23: Voltage metering automatic report time cycle, unit is second
Voltage metering automatic report time cycle, unit is second Size: 4 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 5 - 2678400 | Voltage metering automatic report time cycle, unit is second |
Parameter 24: Current metering automatic report time cycle, unit is second
Current metering automatic report time cycle, unit is second Size: 4 Byte, Default Value: 3600
| Setting | Description |
|---|---|
| 5 - 2678400 | Current metering automatic report time cycle, unit is second |
Parameter 3: Enable/disable to send the basic report
Enable/disable to send the basic report to the Lifeline when the load state changed (When value set as 1, re-power on the dimmer, it will send Basic report automatically Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disable to send Basic report |
| 1 | Enable to send Basic report |
Parameter 31: Setting dimming curve
Setting dimming curve Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | linear dimming |
| 1 | logarithmic dimming |
Parameter 32: Setting startup brightness of the load
Setting startup brightness of the loadValid value: 0~99Note: every time when turn on the load from OFF status, if thetarget brightness is lower than the startup brightness, thebrightness will first go to the startup brightness value thenfall down to the target brightness Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 99 | Setting startup brightness of the load |
Parameter 4: Default fade time
Default fade time (unit is second) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Instantly |
| 1 - 127 | 1 second (0x01) to 127 seconds (0x7F) in 1 second resolution. |
Parameter 5: Setting minimum brightness value
Setting minimum brightness value Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 50 | the bigger the value is, the higher the loads minimum brightness is |
Parameter 6: Setting maximum brightness value
Setting maximum brightness value Size: 1 Byte, Default Value: 100
| Setting | Description |
|---|---|
| 0 - 100 | the maximum brightness value |
Parameter 7: Choose MOSFET driving type
Choose MOSFET driving type Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | trailing edge |
| 1 | leading edge |
Parameter 8: External switch type
External switch type Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Push button switch |
| 1 | normal on/off switch |
| 2 | 3-way switch |
Parameter 9: Enable/disable external switch to be added to and removed from a network
Enable/disable external switch to be added to and removed from a network (when enables this function, triple press the external switch within 1.5 seconds to be added to or removed from a network) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | disable |
| 1 | enable |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.06 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-20076932 |
| Z-Wave Product Id | 0x0438.0x0200.0xD00C |
| Supported Meter Type | Electric Energy |
| Firmware Updatable | Updatable by Consumer by RF |
| Supported Notification Types | Power ManagementSystem |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |