Philio
Flood Multisensor
SKU: PAT02-A
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
This product can be included and operated in any Z-Wave TM network with other Z-Wave TMcertified devices from other manufacturers and/or other applications.All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 4 | Used for returned events. |
| 2 | 4 | Used for Basic set event. |
Configuration Parameters
Parameter 1: Basic Set OFF Level
Setting the BASIC command value.When the flood trigger off(0x00), send the BASIC CC to the group 2. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -127 - 127 | Setting the BASIC command value. |
Parameter 10: Auto Report Battery Time
The interval time for auto report the battery level. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The tick time can setting by the configuration No.20. |
Parameter 13: Auto Report Temperature Time
The interval time for auto report the temperature. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The tick time can setting by the configuration No.20. |
Parameter 14: Auto Report Humidity Time
The interval time for auto report the humidity. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The tick time can setting by the configuration No.20. |
Parameter 15: Auto Report Flood Time
The interval time for auto report the flood state. Size: 1 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 127 | The tick time can setting by the configuration No.20. |
Parameter 2: Basic Set ON Level
Setting the BASIC command value.When the flood trigger on(0xFF), send the BASIC CC to the group 2. Size: 1 Byte, Default Value: -1
| Setting | Description |
|---|---|
| -127 - 127 | Setting the BASIC command value. |
Parameter 20: Auto Report Tick Interval
The interval time for auto report each tick. Size: 1 Byte, Default Value: 30
| Setting | Description |
|---|---|
| -127 - 127 | Units of one minute. |
Parameter 21: Temperature Differential Report
The temperature differential to report. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 127 | The unit is Fahrenheit. |
Parameter 23: Humidity Differential Report
The humidity differential to report. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 60 | The unit is percentage. |
Parameter 5: Operation Mode
Operation mode. Using bit to control. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | Disable the Flood function. |
| 8 | Setting the temperature scale. |
| 32 | Disable the temperature report after event triggered. |
Parameter 6: Mult-Sensor Function Switch
Multisensor function switch. Using bit to control. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 64 | Disable the humidity report after event triggered. |
Parameter 7: Customer Function
Customer function switch, using bit control. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 8 | Disable send out BASIC OFF after the flood event cleared. |
| 64 | Disable to report battery state when the device triggered. |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.01:01.14 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-20026862 |
| Z-Wave Product Id | 0x013C.0x0002.0x0078 |
| Firmware Updatable | Not Updatable |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |