This is a
This product is a multi-channel Z-Wave breaker with built-in S2 security.Built-in high-power relay, multi-type external switch selection.Very convenient.
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave plug lifeline |
2 | 5 | basic set command |
3 | 5 | basic set command |
4 | 5 | basic set command |
Restores state after power failure Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | All Relays OFF |
1 | All relays remember the status prior to power outage and turns back to it |
2 | All relays turned on after power failure |
3 | R1&R2 state recovered, R3OFF |
4 | R1&R2 state recovered , R3-ON |
Relay-3(EP3)Auto Turn-Off Timer Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 65535 | The countdown time, Relay-3 OFF |
Relay-3(EP3)Auto Turn-On Timer Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 65535 | The countdown time, Relay-3 ON |
Realy-1(EP1)Manual Control Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | manual control disabled |
1 | manual control enabled |
Realy-2(EP2)Manual Control Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | manual control disabled |
1 | manual control enabled |
Realy-3(EP3)Manual Control Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | manual control disabled |
1 | manual control enabled |
SW1 Type Select Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | momentary switch |
1 | toggle switch (contact closed -ON, contact opened - OFF) |
2 | toggle switch(device changes status when switch changes status) |
SW2 Type Select Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | momentary switch |
1 | toggle switch (contact closed -ON, contact opened - OFF) |
2 | toggle switch(device changes status when switch changes status) |
SW3 Type Select Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | momentary switch |
1 | toggle switch (contact closed -ON, contact opened - OFF) |
2 | toggle switch(device changes status when switch changes status) |
LED indicator Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | led OFF when output ON,led ON when output OFF |
1 | led ON when output ON,led OFF when output OFF |
2 | led always OFF |
3 | led always ON |
Relay-1(EP1)Auto Turn-Off Timer Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 65535 | The countdown time, Relay-1 OFF |
Relay-1(EP1)Auto Turn-On Timer Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 65535 | The countdown time, Relay-1 ON |
Relay-2(EP2)Auto Turn-Off Timer Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 65535 | The countdown time, Relay-2 OFF |
Relay-2(EP2)Auto Turn-On Timer Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 65535 | The countdown time, Relay-2 ON |
Hardware Platform | ZM5202 |
Device Type | On/Off Power Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.00 |
Z-Wave Version | 6.82.00 |
Certification ID | ZC10-19126825 |
Z-Wave Product Id | 0x0312.0xa000.0xa00a |
Firmware Updatable | Updatable by Consumer by RF |
Color | Black |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |