ABUS
Z-Wave 230V relay module
SKU: PLHA10000
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The dual relay in-wall module contains two sets of relays and switches, with each set dedicated for controlling lighting or an appliance in your home. Each relay can be turned on/off individually using Z-wave commands or using the switches connected to the module. At 230V voltage, this module can support up to 2*4.3A output, 2*1000W resistive load. This unit is to be installed and sealed inside an electrical switch box.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | When the device is powered for the first time, the device sends a notification report to the node of group 1.When a factory reset is performed, the device sends a Reset Locally Notification to the node of group 1.When a relay output is activated by the switch, the device sends a binary switch report to the node of group 1. |
| 2 | 5 | When key 1 is pressed, the device sends a BASIC SET command containing a value to the nodes of group 2.(If the relay output is off, the Basic Set is value=0x00, if the relay output is on, the Basic Set is value=0xFF) |
| 3 | 5 | When key 2 is pressed, the device sends a BASIC SET command containing a value to the nodes of group 3.(If the relay output is off, the Basic Set is value=0x00, if the relay output is on, the Basic Set is value=0xFF) |
Configuration Parameters
Parameter 1: Key 1
0: Momentary button1: Switch (Toggle) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0: Momentary button, 1: Switch (Toggle) |
Parameter 2: Key 2
0: Momentary button1: Switch (Toggle) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | 0: Momentary button, 1: Switch (Toggle) |
Parameter 3: Relay 1 Auto Off Time
0: No Auto Off Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 43200 | 0: No Auto Off |
Parameter 4: Relay 2 Auto Off Time
0: No Auto Off Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 43200 | 0: No Auto Off |
Parameter 5: Remember relay 1 last state
0: do not remember1: remember Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | 0: do not remember, 1: remember |
Parameter 6: Remember relay 2 last state
0: do not remember1: remember Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 1 | 0: do not remember, 1: remember |
Technical Data
| Hardware Platform | SD3502 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.01:00.01 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-19116788 |
| Z-Wave Product Id | 0x0403.0x0003.0x0005 |
| Loads Controlled | 2 |
| Neutral Wire Required | ok |
| Color | White |
| Firmware Updatable | Updatable by Consumer by RF |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |