Jasco
Smart Flood/Freeze Sensor
SKU: 43985 / ZW6306
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Monitor your home from anywhere with the Z-Wave Plus Flood/Freeze Sensor. When paired with a compatible hub, the smart sensor provides notification when water levels or temperatures change.Trigger eventsThe sensor communicates with your hub to initiate desired actions of Z-Wave devices. Increase peace of mind by automatically turning on lights, sending a notification to your phone, activating an alarm or more when temperatures or water levels change.Detection alarmBuilt-in speaker emits audible alert when water levels or temperatures change to allow immediate action by anyone in the area. Dual functionBase contacts and a detachable probe accommodate various setups. Recessed contacts on the base of the sensor are ideal for placement on flat surfaces. The included probe extends reach for use in wells, sump pump holes and other small spaces. Temperature sensorIn temperature-sensitive spaces, protect against costly damage caused by freezing or overheating. Indicator lightLED indicator displays status and provides feedback during programming. It also serves as notification if tampering with the sensor occurs.Universal compatibilityZ-Wave Plus and all previous Z-Wave generations work together to allow continued expansion of your home-automation network.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | This device supports lifeline and notification (association group 1) supporting 5 nodes.Lifeline association supports the device reset locally function. |
Configuration Parameters
Parameter 19: Alternate Exclusion
When enabled, press the button three times quickly when prompted to remove device. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Press the button once when prompted to remove device |
| 1 | Press the button three times quickly when prompted to remove device |
Parameter 21: Reverse detection of wet/dry
Size: 2 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Normal detection(water detected) |
| 2 | Reverse detection(dry detected) |
Parameter 22: Temperature Report Interval (When battery operated)
Size: 2 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 60 | Hourly |
| 5 - 60 | 5-60 Minutes |
| 360 | 6 Hours |
| 720 | 12 Hours |
| 1440 | Daily |
Parameter 23: Battery Report Interval
Size: 2 Byte, Default Value: 1440
| Setting | Description |
|---|---|
| 5 - 60 | 5-60 Minutes |
| 360 | 6 Hours |
| 720 | 12 Hours |
| 1440 | Daily |
Parameter 50: Low Temp Alarm
Notification type: Heat = 04Under limit event = 06Under limit non-event = 00 Size: 2 Byte, Default Value: 33
| Setting | Description |
|---|---|
| -4 - 122 | -4F to 122F |
| 33 | 33F (Default) |
Parameter 51: High Temp Alarm
Notification type: Heat = 04Over limit event = 02Over limit non-event = 00 Size: 2 Byte, Default Value: 104
| Setting | Description |
|---|---|
| -4 - 122 | -4F to 122F |
| 104 | 104F (Default) |
Parameter 52: Temperature Report Interval (When USB operated)
Size: 2 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 5 - 60 | 5-60 Minutes |
| 60 | Hourly |
| 360 | 6 Hours |
Parameter 53: Tamper Alert Configuration
Size: 2 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | (Default) - Red LED continuous flash and beeps |
| 2 | Red LED flashes once, continuous beeps |
| 3 | Red LED continuous flash, no beeps |
| 4 | Red LED flash once, no beeps |
| 5 | No LED, no beeps |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 5.55 |
| Z-Wave Version | 6.81.03 |
| Certification ID | ZC10-19106780 |
| Z-Wave Product Id | 0x0063.0x4953.0x3236 |
| Color | |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |