This is a
The Inovelli dimmer switch is a Z-Wave in-wall dimmer that controls attached LED, CFL, & Incandescent lighting which can be highly customized to your liking at the switch itself with our unique config button and advanced firmware. The switch can also be used either with or without a neutral wire.
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | 1. Basic Report2. Multilevel Report3. Application Status4. Device Reset Locally |
2 | 5 | Basic Set |
3 | 5 | Switch Multilevel Set. Group 3 can be used to keep the, u0022masteru0022 switch in sync with the, u0022slave switchesu0022. |
4 | 5 | SWITCH_MULTILEVEL_START_LEVEL_CHANGE; SWITCH_MULTILEVEL_STOP_LEVEL_CHANGEGroup 4 is so that an accessory switch can control multiple bulbs / dimmers with level change. |
How fast or slow the light turns on when you hold the switch (ie: dimming from 10-20%, 80-60%, etc). Example of how the values are used: 0 = Instant On, 1 = 1 second, 100 = 100 seconds. This parameter can be changed at the config button. NOTE IF USING A DUMB SWITCH: This parameter will not work when pressing the dumb switch manually. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
0 - 100 | Seconds |
Default dim level for the switch when controlled remotely (via an app or voice control). Example of how the values are used: 0 = Switch will return to level it was prior to being off, 1 = 1%, 100 = 100%. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Previous Level |
1 - 100 | Percentage |
When power is restored, the switch reverts to either On, Off, or Last Level. Example of how the values are used: 0 = Off, 1-100 = Specific % On. Entering a value of 101 = Returns the switch to the Level before the Power Outage. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Off |
1 - 100 | Turns On to a Specific Percentage Level |
101 | Turns On to Last Percentage Level |
When should the switch send commands to associated devices. Size: 1 Byte, Default Value: 15
Setting | Description |
---|---|
1 | Local |
2 | 3-Way |
3 | 3-Way + Local |
4 | Z-Wave HUB |
5 | Z-Wave HUB + Local |
6 | Z-Wave HUB + 3-Way |
7 | Z-Wave HUB + Local + 3-Way |
8 | Timer |
9 | Timer + Local |
10 | Timer + 3-Way |
11 | Timer + 3-Way + Local |
12 | Timer + Z-Wave HUB |
13 | Timer + Z-Wave HUB + Local |
14 | Timer + Z-Wave HUB + 3-Way |
15 | All |
This will set the default color of the LED Bar. The color is calculated by using a hue color circle (Value / 255 * 360). See website for more info. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 170
Setting | Description |
---|---|
170 | Default Color (Blue) |
0 - 255 | Colors |
This will set the intensity of the LED bar (ie: how bright it is). Example of how the values are used: 0 = Off, 1 = Low, 5 = Medium, 10 = High. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | Disabled |
1 - 32767 | Seconds |
0 | Off |
1 - 4 | Low Intensity |
5 - 7 | Medium Intensity |
8 - 10 | High Intensity |
This is the intensity of the LED bar when the switch is off. Example of how the values are used: 0 = Off, 1 = Low, 5 = Medium, 10 = High. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Off |
1 - 4 | Low Intensity |
5 - 7 | Medium Intensity |
8 - 10 | High Intensity |
This will allow you to add some sweet effects to your LED bar (ie: pulse, chace, solid, etc). Example of how the values are used: Byte 1 = Choose Color, Byte 2 = Choose Brightness Level, Byte 3 = Choose Effect, Byte 4 = Duration. Please see website for further instructions on how to set this up as you'll have to enter values for each byte. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | No Effect |
Changes the amount of time the RGB Bar shows the Dim level if the LED Bar has been disabled. Example of how the values are used: 0 = Always off, 1 = 1 second after level is adjusted, 10 = 10 seconds after level is adjusted. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
0 | Always Off |
1 - 10 | Seconds after Dim Level is Adjusted |
How fast or slow the light turns on when you dim the switch remotely (ie: dimming from 10-20%, 80-60%, etc). Example of how the values are used: 0 = Instant On, 1 = 1 second, 100 = 100 seconds. A value of 101 keeps this parameter in sync with Parameter 1. Size: 1 Byte, Default Value: 101
Setting | Description |
---|---|
0 | Instant On |
1 - 100 | Seconds |
101 | Keeps in sync with Parameter 1 |
How fast or slow the light turns on when you press the switch 1x to bring from On to Off or Off to On. Example of how the values are used: 0 = Instant On, 1 = 1 second, 100 = 100 seconds. A value of 101 keeps this parameter in sync with Parameter 1. Size: 1 Byte, Default Value: 101
Setting | Description |
---|---|
0 | Instant On |
1 - 100 | Seconds |
101 | Keeps in sync with Parameter 1 |
How fast or slow the light turns on when you turn on or off the switch remotely to bring from On to Off or Off to On. Example of how the values are used: 0 = Instant On, 1 = 1 second, 100 = 100 seconds. A value of 101 keeps this parameter in sync with Parameter 1. Size: 1 Byte, Default Value: 101
Setting | Description |
---|---|
0 | Instant On |
1 - 100 | Seconds |
101 | Keeps in sync with Parameter 1 |
Minimum level the light switch will dim to (great for fixing flickering bulbs). Example of how the values are used: 1= 1%, 2 = 2%, 45 = 45%. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 45 | Percentage |
Maximum level the light switch will dim to. Example of how the values are used: 55= 55%, 56 = 56%, 100 = 100%. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
55 - 100 | Percentage |
Inverts the switch (Tap Down = On, Tap Up = Off). Example of how the values are used: 0 = Disabled, 1 = Enabled. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disabled |
1 | Enabled |
Automatically turns the switch off after x amount of seconds. Example of how the values are used: 0 = Disabled, 1 = 1 second, 32767 = 32767 seconds. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 32767 | automatically turns off after so many seconds |
Default dim level for the switch when pressed locally (at the switch). Example of how the values are used: 0 = Switch will return to level it was prior to being off, 1 = 1%, 100 = 100%. This parameter can be changed at the config button. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Previous Level |
1 - 100 | Percentage |
Hardware Platform | ZM5101 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.24:01.21 |
Z-Wave Version | 6.81.03 |
Certification ID | ZC10-19096763 |
Z-Wave Product Id | 0x031E.0x0003.0x0001 |
Firmware Updatable | Updatable by Manufacturer |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |