REHAU

Rehau RE.GUARD Leakage detector

SKU: 14573121001

ZWave+ Security V2

Quickstart

This is a secure Valve for XXXQFrequencyName. To run this device please make sure the internal battery is fully charged.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Rehau RE.GUARD is a water manager which protects your home against water leakages and meassures your consumption of water.It has a highly sophisticated water meter and pressure meter built inside. Its algorithms are able to detect very small microleakages as well aslarger leakages like e.g. pipe bursts. The sensibility can be adapted to your needs. Furthermore statistics of your water consumption can be created to help you save water.This product is available at your professional plumber.Made and engineered in Europe

Reset to factory default XXXResetDescription
Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Connection to Gateway etc.
2 5 Sends status of valve
3 5 Sends notiofication in case of leackage

Configuration Parameters

Parameter 1: operation mode


Size: 1 Byte, Default Value: 2

Setting Description
0 0-valve (always) off
1 1-user absent=not at home=holiday
2 2 = user present=at home
3 3 = valve (always) on

Parameter 10: micro leakage pressure drop abort


Size: 2 Byte, Default Value: 100

Setting Description
0 - 32000 pressure drop in kPa

Parameter 11: number of measurements

for micro leackage
Size: 1 Byte, Default Value: 3

Setting Description
1 - 99 how many in one time period

Parameter 12: wait time until next measurement


Size: 1 Byte, Default Value: 1

Setting Description
0 - 60 waiting time in minutes between two meassurements

Parameter 13: reaction to micro leakage


Size: 1 Byte, Default Value: 0

Setting Description
0 - 2 0=disable detection, 1=blink LED, 2= blink LED andshut off valve

Parameter 14: macro leakage detected


Size: 1 Byte, Default Value: 0

Setting Description
0 no leackage
1 leackage detected

Parameter 15: max flow rate if operation mode is 2


Size: 2 Byte, Default Value: 3000

Setting Description
0 - 32000 flowrate in l/h

Parameter 16: max pressure drop if operation mode is 2


Size: 2 Byte, Default Value: 1000

Setting Description
0 - 32000 pressure drop in kPa

Parameter 18: max continious liter if operation mode is 2


Size: 2 Byte, Default Value: 300

Setting Description
0 - 32000 liter

Parameter 20: max continious time if operation mode is 2


Size: 2 Byte, Default Value: 60

Setting Description
0 - 32000 time in minutes for water flow in present mode

Parameter 21: max flow rate if operation mode is 1


Size: 2 Byte, Default Value: 300

Setting Description
0 - 32000 max flow rate in absent mode liters/hour

Parameter 22: max pressure drop if operation mode is 1


Size: 2 Byte, Default Value: 1000

Setting Description
0 - 32000 max pressure drop in absent mode

Parameter 24: max continious liter if operation mode is 1


Size: 2 Byte, Default Value: 100

Setting Description
0 - 32000 max. liter of water in absent mode

Parameter 26: max continious time if operation mode is 1


Size: 2 Byte, Default Value: 30

Setting Description
0 - 32000 max. time of water flow in absent mode in minutes

Parameter 28: reaction to macro leakage

0=disable detection, 1=blink LED, 2= blink LED and shut off valve
Size: 1 Byte, Default Value: 2

Setting Description
0 - 2 0=disable detection, 1=blink LED, 2= blink LED and shut off valve

Parameter 30: reaction to flooding sensor

0=disable detection, 1=blink LED, 2= blink LED andshut off valve
Size: 1 Byte, Default Value: 1

Setting Description
0 - 2 0=disable detection, 1=blink LED, 2= blink LED andshut off valve

Parameter 31: backup battery nominal voltage


Size: 2 Byte, Default Value: 0

Setting Description
0 - 7 shows backup battery voltage

Parameter 37: time set correctly


Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 0=time not set 1=time set correctly

Parameter 38: total operating time


Size: 4 Byte, Default Value: 0

Setting Description
0 - 2147483647 Read only: Counting total operation time internally

Parameter 39: operating time since last power on


Size: 4 Byte, Default Value: 0

Setting Description
0 - 2147483647 Read only counting operation time since last power off

Parameter 4: fixed schedule time hours


Size: 1 Byte, Default Value: 0

Setting Description
0 - 23 hour of day

Parameter 5: fixed schedule time minutes

minutes in time stamp
Size: 1 Byte, Default Value: 0

Setting Description
0 - 59 minute

Parameter 50: water temperature high threshold


Size: 2 Byte, Default Value: 250

Setting Description
0 - 32000 1C = 10; Recommended 25C by international standards

Parameter 51: water temperature low threshold


Size: 2 Byte, Default Value: 20

Setting Description
0 - 32000 1C = 10; Water icing prevention

Parameter 54: error code

error codes; see documentation for
Size: 1 Byte, Default Value: 0

Setting Description
0 - 37 showing different error codes. See website for error description

Parameter 6: fixed schedule day

127 = 1111111 in binary, 0 -> automatic schedule time interval is used, see u0022data_definiton_commentu0022
Size: 1 Byte, Default Value: 127

Setting Description
1 - 127 1111111 in binary,

Parameter 7: automatic schedule time interval


Size: 2 Byte, Default Value: 0

Setting Description
0 - 168 How many days

Parameter 8: micro leakage mesuring time


Size: 2 Byte, Default Value: 100

Setting Description
0 - 32000 seconds measuring time

Parameter 9: micro leakage pressure drop


Size: 2 Byte, Default Value: 0

Setting Description
0 - 32000 presssure drop in kPa

Technical Data

Hardware Platform ZM5101
Device Type Valve
Network Operation Always On Slave
Firmware Version HW: 1 FW: 1.05:01.06
Z-Wave Version 6.71.03
Certification ID ZC10-19096760
Z-Wave Product Id 0x0413.0x0001.0x0001
Frequency XXfrequency
Maximum transmission power XXantenna
Valve