This is a
This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.Each module is designed to act as a repeater,which will re-transmit a radio frequency (RF) signal by routing the signal ,around obstacles and radio dead spots to ensure that the signal is received at its intended destination.
Reset to factory default | XXXResetDescription |
Inclusion | XXXInclusionDescription |
Exclusion | XXXExclusionDescription |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Z-Wave Plus Lifeline |
2 | 5 | basic set command |
Locally Button function Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Up Button ON,Down Button OFF |
1 | Up Button OFF,Down Button ON |
2 | Up Button: On/OffDown Button: On/Off |
Multilevel minimumvalue can be setThe minimum luminance value of the dimmingLocal Button Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 - 99 | Multilevel minimumvalue can be setThe minimum luminance value of the dimmingLocal Button |
Multilevel maxmum value can be setThe maxmum luminance value of the dimmingLocal Button Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 99 | Multilevel maxmum value can be setThe maxmum luminance value of the dimmingLocal Button |
when switch is off and quickly press UPPER paddle 2 times, switch turns on to x brightness Local Button Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Turn ON to 99 |
1 | turn on to the value relate |
Double Tap Behavior Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | enable double tap to full brightness |
1 | disable double tap to full brightness, single tap to last brightness level |
2 | disable double tap to full brightness, single tap always to full brightness |
Enable or Disable local control Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | disable |
1 | enable |
Status LED Configuration Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Output and the LED are in the different state. |
1 | Output and the LED are in the same state. |
2 | Always OFF |
3 | Always ON |
Enable Auto Turn-OFF Timer Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Auto Turn-OFF Timer Disabled |
1 | Auto Turn-OFF Timer Enabled |
Count Down Configuration(Turn off the output by time Size: 4 Byte, Default Value: 60
Setting | Description |
---|---|
1 - 65535 | Count Down Configuration(Turn off the output by time |
Enable Auto Turn-ON Timer Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Auto Turn-ON Timer Disabled |
1 | Auto Turn-ON Timer Enabled |
Count Down Configuration(Turn ON the output by time Size: 4 Byte, Default Value: 60
Setting | Description |
---|---|
1 - 65535 | Count Down Configuration(Turn ON the output by time |
Association Setting Parameter Size: 1 Byte, Default Value: 15
Setting | Description |
---|---|
0 | None |
1 | Local |
2 | 3-way |
3 | 3-way&Local |
4 | Z-Wave hub |
5 | Z-Wave hub&Local |
6 | Z-Wave hub&3-way |
7 | Z-Wave hub&Local&3-way |
8 | Timer |
9 | Timer&Local |
10 | Timer&3-way |
11 | Timer&3-way&Local |
12 | Timer&Z-Wave hub |
13 | Timer&Z-Wave hub&Local |
14 | Timer&Z-Wave hub&3-way |
15 | ALL |
Restores state after power failure Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | Output OFF. |
1 | Output ON |
2 | The state before a power outage. |
Dimmer Speed Parameter Local Button Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 - 99 | from 0x63 to 0x00 or from 0x00 to 0x63 need XXs |
Hardware Platform | ZM5202 |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Firmware Version | HW: 1 FW: 1.00 |
Z-Wave Version | 6.81.03 |
Certification ID | ZC10-19086704 |
Z-Wave Product Id | 0x0312.0xA000.0xAA02 |
Z-Wave Scene Type | Scene |
Switch Type | Toggle |
Firmware Updatable | Updatable by Consumer by RF |
Electric Load Type | Dimmable LEDIncandescent |
Color | White |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |