myTEM SmartHome
Radio Switch Dual Plus
SKU: MTSWI-101-WL
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The myTEM Radio Switch Dual Plus is a universal, Z-Wave compatible wall or ceiling switch (ON/OFF) and is used to control two electrical devices. Two additional digital inputs and the programmable behav-ior to the wireless commands allow flexible use in the house. Optionally, a myTEM Touch Add-on control panel can be attached to the connector.The device is intended for installation in a flush-mounted box.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus LifelineSystem / Heartbeat; sent periodically (see Configuration Parameter Heartbeat)Power Mangement / Power has been applied; sent after Powerup and Reset |
| 2 | 5 | Binary Switch Report; sent when the output 1 changes state |
| 3 | 5 | Binary Switch Report; sent when the output 2 changes state |
| 4 | 5 | Binary Sensor Report; sent when the input 1 changes state |
| 5 | 5 | Binary Sensor Report; sent when the input 2 changes state |
Configuration Parameters
Parameter 1: Heartbeat Rate
If the notification System Heartbeat is on, a notification report System Heartbeat is sent periodically every 60 minutes (default value). Size: 2 Byte, Default Value: 60
| Setting | Description |
|---|---|
| 1 - 1440 | Heartbeat rate [min] |
Parameter 2: Send Interval Temperature
Period with which the measured temperature is sent by a Multilevel Sensor Report. Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 120 | Send interval temperature [min] |
Parameter 3: Minum Delta Temperature Send
When the temperature changes this anount the temperature value is sent by a Multilevel Sensor Report. Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 100 | Minimum delta temperature [0.1 K] |
Parameter 4: Send Interval Humidity
Period with which the measured humidity is sent by a Multilevel Sensor Report. Size: 2 Byte, Default Value: 30
| Setting | Description |
|---|---|
| 1 - 120 | Send interval humidiy [min] |
Parameter 5: Minimum Delta Humidity Send
When the humidity changes this anount the temperature value is sent by a Multilevel Sensor Report. Size: 2 Byte, Default Value: 10
| Setting | Description |
|---|---|
| 10 - 1000 | Minimum delta humidity [0.1 %] |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-19076686 |
| Z-Wave Product Id | 0x034E.0x0001.0x0008 |
| Electric Load Type | ELV (Electronic)IncandescentInductive (e.g. Motor) |
| Loads Controlled | 2 |
| Supported Notification Types | Power ManagementSystem |
| Firmware Updatable | Updatable by Consumer by RF |
| Switch Type | Push Button |
| Color | White |
| Sensors | Air TemperatureHumidity |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |