LUX
KONOzw Smart Hub Thermostat
SKU: KN-ZW-WH1-B04
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
KONOzw is the smart hub thermostat made with you in mind. It seamlessly connects to many smart hubs and blends in or stands out with its interchangeable Dcorsnap covers. KONOzw makes it easier than ever to personalize your comfort, dcor, and savings.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: User Temperature Calibration
User Temperature Calibration. For example, sending a value of +50 means the calibration offset is +0.5F Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -250 - 250 | Step-size = 10 |
Parameter 10: Temperature Limit - Cool Max
Size: 2 Byte, Default Value: 95
| Setting | Description |
|---|---|
| 60 - 95 | Increment by 1F. The actual allowable range is dependent on the heat set point limit |
Parameter 11: Temperature Limit - Cool Min
Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 50 - 75 | Increment by 1F. The actual allowable range is dependent on the heat set point limit |
Parameter 12: Temperature Minimum Setpoint Deadband
Temperature Minimum Setpoint Deadband. For example, setting the value to 200 means the deadband is +2.0F Size: 2 Byte, Default Value: 200
| Setting | Description |
|---|---|
| 100 - 250 | Step-size = 10 |
Parameter 14: Ambient Temperature Change Stepsize
Degree of change in ambient temperature in order to trigger the sending of temperature report Size: 2 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 50 | 0.5F |
| 100 | 1.0F |
| 150 | 1.5F |
| 200 | 2.0F |
| 250 | 2.5F |
| 300 | 3.0F |
| 350 | 3.5F |
| 400 | 4.0F |
Parameter 15: Regular Ambient Temperature Reporting Interval
Regular Ambient Temperature Reporting Interval Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 24 | 1-24 hours |
Parameter 16: Regular Operating State Reporting Interval
Regular Operating State Reporting Interval Size: 1 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 1 - 24 | 1-24 hours |
Parameter 17: Command Echo Enable
Command Echo for- Thermostat Mode- Thermostat Fan mode- Thermostat Setpoint Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disable |
| 1 | Enable |
Parameter 2: Temperature Unit (C/F)
Temperature Unit (C/F) Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Celsius |
| 1 | Fahrenheit |
Parameter 3: Available Control mode
Available Control mode Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Heat and Cool, Auto |
| 1 | Heat Only |
| 2 | Cool Only |
| 3 | Heat and Cool, no Auto |
| 4 | reserved |
Parameter 4: System Type
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Furnace Gas |
| 1 | Furnace Electric |
| 2 | Heat Pump |
| 3 | Boiler no fan |
| 4 | reserved |
Parameter 5: Reversal valve Type in Heat Pump
Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | O-valve |
| 1 | B-valve |
Parameter 8: Temperature Limit - Heat Max
Size: 2 Byte, Default Value: 90
| Setting | Description |
|---|---|
| 60 - 90 | Increment by 1F |
Parameter 9: Temperature Limit - Heat Min
Size: 2 Byte, Default Value: 45
| Setting | Description |
|---|---|
| 45 - 60 | Increment by 1F |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Thermostat - HVAC |
| Network Operation | Always On Slave |
| Firmware Version | HW: 2 FW: 1.00:00.114 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-19076681 |
| Z-Wave Product Id | 0x0411.0x0001.0x2111 |
| Thermostat Power Source | |
| Sensors | |
| Loads Controlled | |
| Thermostat Modes | |
| Color | |
| Firmware Updatable | |
| Thermostat HVAC Systems Supported | |
| Supported Notification Types | |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |