Aeotec
Door/Window Sensor 7
SKU: ZWA008-B
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Aeotec Door/ Window Sensor 7 is a small window position sensor for your smart home, it monitors window and their exact opening position and lets your know when a window is tilted or completely opened. It also supports connecting external binary sensors through the dry binary contact of the Door/ Window sensor.
| Reset to factory default | XXXResetDescription |
| Inclusion | XXXInclusionDescription |
| Exclusion | XXXExclusionDescription |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Z-Wave Plus Lifeline |
| 2 | 5 | Control devices when magnet or external dry contacts trips |
| 3 | 5 | Sends our alarm message when magnet controlled or external dry sensor trips. |
| 4 | 5 | Sends alarm messages when tamper is tripped |
Configuration Parameters
Parameter 1: Sensor Operation Mode
This parameter defines if the internal magnet sensor or the external terminal input is detected and used to issue alarm notification. There is always one input active only. The other sensor input the deactivated. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Internal Magnet Sensor Used |
| 1 | External Terminal Inputs Used |
Parameter 10: Time Delay of Off command frame
Off command is sent after a delay defined in this parameter. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 32400 | seconds |
Parameter 11: Delay of Tamper Alarm Cancellation
Time a tamper alarm is delayed. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 32400 | seconds |
Parameter 12: Reporting Tamper Alarm Cancellation
This parameter defines if the alarm cancellation event is reported. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Do not send Report |
| 1 | Send Report |
Parameter 13: Central Scene Event Functionality
This parameter enables/disablesthe central scene function. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 14: Tilt Sensor Functionality
This parameter enables/disablesthe tilt function. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 2: Sensor State Polarity
This parameter defines the polarity of the magnet sensor. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Closed when Magnet in proximity |
| 1 | Opened when Magnet in proximity |
Parameter 3: Visual LED Indications
This parameter defines when the red LED will indicate events. Disabling all indications may extend battery life. Size: 1 Byte, Default Value: 7
| Setting | Description |
|---|---|
| 1 | No Indications |
| 2 | Open/Close Status Change |
| 4 | Wake Up |
| 16 | Device Tampering |
Parameter 4: Range Test after double click
Allows to enable the activation of a Z-Wave range test with double clicking the tamper switch. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 5: 2nd Association Group Trigger
his parameter defines the status of the magnet switch that causes sending a BASIC command to all devices of Association Group 2. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Switch after Open and Close |
| 1 | Switch after Open |
| 2 | Switch after Close |
Parameter 6: Command Sent to Devices of Association Group 2
This parameter defines which commands is sent to 2nd Association Group Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 0 | On |
| 1 | Off |
| 2 | On and Off |
Parameter 7: BASIC command value sent to 2nd Association Group on On event
This is the BASIC command value sent in case of On event. Size: 1 Byte, Default Value: -1
| Setting | Description |
|---|---|
| -1 | Value |
| 0 - 99 | Value |
Parameter 8: BASIC command value sent to 2nd Association Group on Off event
This is the BASIC command value sent in case of Off event. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| -1 | Value |
| 0 - 99 | Value |
Parameter 9: Time Delay of Off command frame
Off command is sent after a delay defined in this parameter. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 32400 | seconds |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 1 FW: 1.00 |
| Z-Wave Version | 6.81.01 |
| Certification ID | ZC10-19076678 |
| Z-Wave Product Id | 0x0371.0x0202.0x0007 |
| Sensors | Open/Closed (Binary) |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Supported Notification Types | Access ControlHome SecurityPower Management |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |