Yale
Digital Door Lock
SKU: YDM4109+
Quickstart
This is a
To include:1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'I' button [Registration] from the inside of battery cover.4. Press 9,#,1,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play then press 'I' button
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Digital Doorlock by YaleManufacturer: iRevo, ASSA ABLOYThe Yale Digital Door Lock Collection, Smarter Solution for your home, High tech Fingerprint Digital Door Lock with strong featuresFeatures:One touch Fingerprint Verification Method (Progressive Scan)Automatic LockingVoice Guide FeatureSmart TouchpadScramble codeEmergency Mechanical KeyAnti-panic egress with Safe handleAutomatic Alarm (Break-in/Damage)Low-battery alarm and emergency power supply terminalTechnical details:Mortise Lock TypeFingerprint: Up to 20Mechanical Keys: 2 KeysPin Code: 6-12 digitsColour: BlackOutside Trim Dimensions : 28.5mm X 68.6mm X 320.7mmThickness : Suitable for 40-80mm thick wooden doorsBackset : 60mm
| Reset to factory default | To reset to factory defaults:Please use this procedure only when the network primary controller is missing or otherwise inoperable. (User code or master code remains the same. Only network settings reset to factory defaults.) 1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'I' button [Registration] from the inside of battery cover.4. Press 9,#,9,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play then press 'I' button |
| Inclusion | To include:1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'I' button [Registration] from the inside of battery cover.4. Press 9,#,1,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play then press 'I' button |
| Exclusion | To exclude:1. Touch keypad with palm2. Enter User code(Normal Mode only. Enter Master code if operating Master Mode.)3. Press 'I' button [Registration] from the inside of battery cover.4. Press 9,#,3,# on the keypad (by sequence)5. Wait until 'Ding dong dang' melody play then press 'I' button |
| NIF | XXXNIF |
| Wakeup | The lock is always in 'Wake up status'.However, touch with palm to begin and end action. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 5: English Language
Set the language of the Door Lock interface Size: 1 Byte, Default Value: 2
| Setting | Description |
|---|---|
| 1 | Korean Language |
| 2 | English Language |
| 3 | Chinese Language |
| 6 | Taiwanese Language |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Door Lock - Keypad |
| Network Operation | Listening Sleeping Slave |
| Firmware Version | HW: 32 FW: 33.17:17.16 |
| Z-Wave Version | 6.71.03 |
| Certification ID | ZC10-19076673 |
| Z-Wave Product Id | 0x0129.0xC700.0x0005 |
| Door Lock Type | Lever Handle |
| Communications Connections | BluetoothManufacturer Proprietary |
| Supported Notification Types | Access ControlEmergency AlarmHome SecurityPower Management |
| Color | Silver |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |