Quickstart
This is a
secure
Notification Sensor for XXXQFrequencyName.
To run this device please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.1. Insert the 3V CR123A Lithium battery into the battery compartment connecting the correct polarity as shown on the battery compartment lid.2. Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).3. Within 1 second, press the Function Button 3 times. 4. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.5.If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from
Z-Wave Alliance Product
data and may be incomplete. Please refer to the
Manufacturers Manual for more information.
Product Description
ACGS-23ZW Acoustic Glassbreak Sensor is an excellent first line of defense for perimeter protection. This wireless sensor will alert when a glass window or door is being smashed or broken, providing an extra layer of advanced security for your property.Our proprietary microphone technology recognizes acoustic patterns to provide full coverage, with a maximum of 8m radius from sensor to glass. With four selectable sensitivity levels, ACGS-23ZW can be easily adjusted to fit large or small rooms. It can also be integrated into security system to activate a siren upon glass break, thereby detering burglars and preventing a full break-in.
| Reset to factory default |
Factory Reset(Only use factory reset when network Control Panel/Gateway is missing or inoperable).1. Remove the batteries of the Glass Break Detector first.2. Press and hold the Function Button. While holding the Function Button, power on the Glass Break Detector by re-inserting the batteries, wait for 10 seconds to factory reset.1. Factory resetting the Glass Break Detector will restore it to factory default settings (excluded from the Z-Wave network). The Z-Wave gateway or control panel will still keep its Z-Wave settings. Please refer to the gateway or control panel manual on how to remove the Glass Break Detectors Z-Wave settings. |
| Inclusion |
This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufactures and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.1. Insert the 3V CR123A Lithium battery into the battery compartment connecting the correct polarity as shown on the battery compartment lid.2. Put the Z-Wave gateway or control panel into Inclusion or Learning mode (please refer to the Z-Wave gateway or control panel manual).3. Within 1 second, press the Function Button 3 times. 4. Refer to the operation manual of the Z-Wave gateway or control panel to complete the learn-in process.5.If the sensor has already been included (learnt) into another Z-Wave Gateway/Control Panel, or if the sensor is unable to be learnt into the current Z-Wave Gateway/Control Panel, please exclude it first (see Exclusion) before attempting to include it into the current Z-Wave Gateway/Control Panel. |
| Exclusion |
The Glass Break Detector must be removed from existing Z-Wave network before being included into another. There are two methods available to exclude a device.Exclusion Mode1. Put the Z-Wave gateway or control panel into Exclusion mode (please refer to the Z-Wave gateway or control panel manual).2. Within 1 second, press the Function Button 3 times and the Glass Break Detector will be removed from the Z-Wave network. |
| NIF |
XXXNIF |
| Wakeup |
This function uses the Z-Wave Wake Up Command Class. The Wake Up Command Class allows the battery-powered Glass Break Detector to notify the Control Panel/Gateway that it is awake and ready to receive any queued commands. The wake up time is programmed automatically according to Control Panels setting when The Glass Break Detector is included. The recommended setting of the wake up time is 60 minutes above. |
| Protection |
XXXProtection |
| FirmwareUpdate |
XXXFirmwareUpdate |
| SetAssociation |
XXXSetAssociation |
Association Groups:
| Group Number |
Maximum Nodes |
Description |
| 1 |
1 |
Group 1 for LifeLine (max node = 1):Notification CC,V3 (COMMAND_CLASS_NOTIFICATION)Battery CC (COMMAND_CLASS_BATTERY)Device Reset Locally CCNotification Report1. If Glass Break Detector is triggered, it will send a Notification Report (Type: 0x07, Event 0x06).2. If tamper is open, it will send Notification Report (Type: 0x07, Event: 0x03)3. If tamper is closed, it will send Notification Report (Type: 0x07, Event: 0x00, Parmeter:0x03).Battery Report1. If battery level changes, it will send Battery Report (0x64, 0x4B, 0x32, 0x19, or 0xFF) respectively.0x64 --- 100% Battery Full0x4B --- 75% Battery0x32 --- 50% Battery0x19 --- 25% Battery0xFF --- Battery Dead (Cut Off)Device Reset1. To perform factory reset, press and hold the Function Button for 10 seconds, the device will send a DEVICE_RESET_LOCALLY_NOTIFICATION report. |
| 2 |
1 |
Group 2 for Basic Set (max node = 1):BASIC CC (COMMAND_CLASS_BASIC)1. When the detector is triggered, it will send BASIC SET (0xFF). The device does NOT support Restore Event report. |
Technical Data
| Hardware Platform |
ZM5202 |
| Device Type |
Notification Sensor |
| Network Operation |
Reporting Sleeping Slave |
| Firmware Version |
HW: 255 FW: 4.01 |
| Z-Wave Version |
6.81.04 |
| Certification ID |
ZC10-19066571 |
| Z-Wave Product Id |
0x018E.0x0003.0x000E |
| Firmware Updatable |
Updatable by Consumer by RF |
| Supported Notification Types |
Home Security |
| Frequency |
XXfrequency |
| Maximum transmission power |
XXantenna |
