Sensative
Strips-MaZw
SKU: 11 01 014
Quickstart
This is a
Strips is delivered in "auto-add" mode. Follow the process below to add Strips in a Z-Wave network.1. Start the add mode on the Z-Wave controller. See the controllers manual.2. Remove both magnets from Strips. Strips blinks twice to confirm the command and successful addition. 3. A long LED blink indicates that the add process was successful4. The Z-Wave controller application should now allow you to monitor your Strips sensor status.5. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly.6. If the Z-Wave system does not respond, it may be needed to change Strips notification type.Manual add:1. Set the controller to add mode(See your controllers manual).2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the add process was successful.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Strips Guard is an ultra-thin magnetic sensor designed to monitor windows and doors for your safety. Its so thin that it can be mounted invisibly in the tiny gap between the frame and the door or window. It is as easy to mount as a sticker using Strips'sadhesive tape.Strips Guard is Z-Wave plus compliant and can be used with any existing Z-Wave smarthome systems.
| Reset to factory default | Please use this procedure only when your Z-Wave controller is missing or otherwise inoperable:1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds.3. On the 3rd repetition, leave the magnet at the rounded edge for 10s. 4. A long LED signal indicates success. |
| Inclusion | Strips is delivered in "auto-add" mode. Follow the process below to add Strips in a Z-Wave network.1. Start the add mode on the Z-Wave controller. See the controllers manual.2. Remove both magnets from Strips. Strips blinks twice to confirm the command and successful addition. 3. A long LED blink indicates that the add process was successful4. The Z-Wave controller application should now allow you to monitor your Strips sensor status.5. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly.6. If the Z-Wave system does not respond, it may be needed to change Strips notification type.Manual add:1. Set the controller to add mode(See your controllers manual).2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the add process was successful. |
| Exclusion | 1. Set the controller in remove mode(See your controllers manual).2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the remove process was successful. |
| NIF | XXXNIF |
| Wakeup | Wake up Strips manually for Z-Wave communication:1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. 3. Repeat 3 times in total within 10 seconds. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Z-Wave Plus Lifeline |
Configuration Parameters
Parameter 1: Notification type
User can use this configuration parameter to change the notification type compatible with their gatewaycontroller. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Binary Sensor report |
| 1 | Notification report |
| 2 | Basic report |
Parameter 2: LED indication
LED On during specific event detected (ex. door opened) else if the parameter value is 0, LED will be turned OFF for the specific event detected. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Specific event indication (ex. door opened) Off |
| 1 | On |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | Notification Sensor |
| Network Operation | Reporting Sleeping Slave |
| Firmware Version | HW: 3 FW: 0.10:00.10 |
| Z-Wave Version | 6.51.10 |
| Certification ID | ZC10-19066531 |
| Z-Wave Product Id | 0x019A.0x0003.0x0003 |
| Color | White |
| Supported Notification Types | Access ControlHome Security |
| Sensors | Open/Closed (Binary) |
| Outdoor Use | ok |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |